Let’s face it—halogen and incandescent headlight bulbs are a thing of the past. fanless, driverless LED headlight bulbs were used in this installation.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points. Repeat these tape lines for your other headlight.

6. Remove your headlight assembly if necessary, remove the current bulbs, and install your new LED bulbs. Check your owner’s manual for specific instructions on how to replace your headlight bulbs.

7. Depending on your vehicle, you may have to adjust your headlight beam before or after the assembly has been reinstalled. Your owner’s manual will explain how to adjust the beams. Align each headlight so that the top edge of the beam is at the same height as your horizontal line(s). If your headlights can be adjusted horizontally or produce two light cutoff points, use the vertical tape lines to align them properly.

3. Shake the vehicle to ensure that your suspension system is settled. For more precise adjustments, inflate all tires to their designated psi capacity and have someone sit in the driver’s seat. Also, make sure that your vehicle’s gas tank is at least half full.

4. Measure from the ground to the center of your headlight assembly where the bulb is located. This step must be done for all vehicles. If your vehicle allows for horizontal headlight adjustments in addition to vertical adjustments, it’s important that you also measure the distance between the centers of both headlight bulbs. The vehicle featured in this video allows for vertical headlight adjustments only; therefore, center lines aren’t necessary but are shown for demonstration purposes.

5. Turn on your low-beam headlights. Using painter’s tape, mark your headlight measurements on a flat wall. Measure from the ground up, and apply a horizontal line of tape to the wall; this line represents the top of your headlight beam. You can either apply one long, continuous line or small sections where the brightest areas of the headlight beams are shown.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points.

If you are looking for ways to save money this summer, you should consider having a staycation rather than a luxurious vacation. Virginia offers great spots to spend a romantic weekend or a weeklong getaway. Not only will this save you money this summer, it will also give you a chance to explore the beautiful state you call home! The wonderful thing about Virginia is how many options there are when it comes to family travel. As cliché as it sounds, there really is something for everyone. Check out these great ideas for a nice mini vacation right here in Virginia!

Stay a Weekend at the Smithfield Station Lighthouse

Smithfield Station Inn offers an exact replica of the Hooper Straight Light and is equipped with two luxurious suites. You can rent a single suite or rent the entire lighthouse and enjoy breathtaking river views complete with all the amenities of a home. Sitting outside and watching the sunset on the East Coast is a perfect way to relax on your weekend getaway.

Hike Some Mountains in Virginia

So when customers ask us how many ‘Watts” do I need to replace an existing light source, we always convert them to lumens.

•  Pay special attention to the lumens per watt of a fixture. IT DOES MATTER. A LED product at 135 lumens/watt will consume far less energy than a LED product producing 97 lumens/watt. Not all LED solutions are the same. (remember, always buy on the lumens you need, never on the watts you think you need.).

•  To calculate lumens per watt, take the total number of lumens a product produces and divide it by the watts it consumes.

For indoor fixtures, figure on:

utility company. You can check if a product is DLC Qualified on the DesignLights Consortium website. DLC has rebates for Commercial LED Lighting and Industrial LED Lighting

•  Rebates with DLC Premium should be higher than rebates with DLC Standard. Your utility company is typically who provides the rebates and sets the rebate amounts.  Check their website.

•  All UL Listed or ETL Listed.

•  Replacing the light parts of an existing fixture with the a Retrofit unit will not void the UL/ETL Listing of the fixture. However, the exception to this rule are explosion proof rated fixtures (ie. Class I Div 2). Never retrofit a certified explosion proof fixture. UL1598C does not cover these types of retrofits.

•  ETL Listing is the same as UL Listing. They perform the same test, and the certification is the same. The only difference is that the company who performs the test.

Are you still struggling to lower your electric bill? Maybe you have made a conscious effort to turn off lights and shorten your showers and you are not seeing that big of a difference. There is more you can do that will not change the way you go about your daily routine. It is by reducing your phantom power usage. What is phantom power, you ask? An electrician in Glendale, like those at The Electric Connection is here to explain what phantom power is and why it is costing you money every month.

Phantom power is the electricity that is used by anything that is plugged in. Your toaster, your cell phone charger and even your television are all pulling a small current even when they are not powered on. Just because you shut off your television, it doesn’t mean it isn’t using electricity. To reduce phantom power, you will need to unplug things that you are not using. When you leave for work in the morning or before you go to bed at night, unplug anything you won’t be using. You may discover you don’t use your toaster for a week.

Phantom power isn’t costing you a ton of money, but when you reduce the amount of phantom power you are pulling, you can help add to the savings you have already implemented. By combining your phantom power reduction, limiting the lights and taking shorter showers, you can save more than 20 dollars a month on your Glendale electrical bill. As you know, every dollar saved counts. You can help make reducing your phantom power a little easier by using power strips in areas where there are several items that are plugged in, like your entertainment area or computer area. Unplugging a single power strip is much easier than unplugging numerous devices. If you have any questions about phantom power or would like to learn more about energy savings, give The Electric Connection a call today.