It’s never a good idea to use electricity around water; bathroom spaces always have a certain amount of humidity and steam as well as water in them. You may end up using electrical devices such as hair dryers and shavers when you are in this bathroom and the shower and bathtub areas always have some water. These can prove to be an electrocution hazard or a fire hazard and it’s important to be extra careful when you are using any electrical appliances in the bathroom.

We all need water to maintain health and hygiene. However, it’s also an excellent conductor of electricity. This means you can easily experience shock when you are standing in a water puddle and touch an electrical appliance. If your skin in wet, that gives the electricity an easier path and it can pass through your body in an unhindered manner.

That can be extremely dangerous as electrical shock can cause heart arrhythmia, burns and can damage your nervous system and lead to death too. If the grounding is improper or if the wiring is poorly installed, that can start a fire as well. And so, it is crucial to maintain electrical safety when you are in bathroom spaces.

Here are some useful tips to you can follow to avoid an emergency:

We handle all types of commercial as well as residential electrical installation, repair and upgrade jobs. For any more information about our services and quotes, contact the Allround Electricals team at this number – 1300 169 263. Alternatively, you can write to us at our email address.

Thanks for reading,1300 169 263

2. In order to open the headlight housing, it must be heated to soften the glue that seals it. Preheat the oven to 270 degrees Fahrenheit, and place the housing in the oven (top rack). Heat the housing for approximately seven minutes. Note that this time will vary by vehicle manufacturer and that you should be careful not to overheat your assembly. Also note that the headlight will be hot when removing it from the oven, so take care not to burn yourself.

*Please note that this can damage your headlight assembly and that you do so at your own risk.

4. LED angel eye installation will vary by headlight. In this instance, we mounted an

5. Place the second layer back in the housing to ensure that everything is aligned the way you would like. This is also a great time to clean the inside housing, as you will not be able to do so once you reseal it. The cleaner you get it the better; smudges and dirt will be more visible when the lights are on.

8. Now it’s time to reseal the headlight housing. Preheat the oven to 270 degrees again, place the layers together, and put the headlight in the oven (with halo rings installed) for seven minutes. Remove the headlight from the oven, and press the layers together firmly as you work around the lens to ensure all of the edges are sealed (this might require gloves, as the headlight will be somewhat hot). Be careful to only press on the edges so as not to warp the lens.

*Please note that this can damage your headlight assembly and that you do so at your own risk.

10. With the headlight housing installed, complete your wiring, and test connections to ensure proper installation. Be sure to tape/heat-shrink any wiring connections that were added, and clean up any loose wiring.

The MD, DC, and VA area is known for getting slammed with violent and powerful thunderstorms that produce severe lightning. Electrical surges, which are caused by lightning, can wreak havoc on your expensive electronics and appliances.

A lightning strike that hits a power line several miles away from your house can impact all your electronic items. Whole-house surge protection is the best option you have to protect your home electronics and wiring from the damage caused by lightning strikes.

Everyone from the National Fire Protection Association to the Institute for Business and Home Safety recommends the use of whole-house surge protection. As a homeowner, the good news for you is that protection is readily available, and even top-of-the-line solutions are affordable. The gold standard in whole-house surge protection is a two-tiered system—a whole-house surge protective device, or SPD, installed at the circuit breaker box, and plug-in SPDs on individual outlets. A whole-house SPD can protect against up to 40,000 amps of current flowing into your home from the outside; normal household power is between 200 to 300 amps. When an electrical surge occurs as a result of a lightning strike, the device detects the excess current and safely diverts it through the house’s grounding path. Whole-house surge protection provides homeowners in MD, DC, and VA peace of mind when a powerful thunderstorm passes the area.

Whole-house surge protection can typically be installed in a home for around $200—it’s an easy job for a top electrician. The cost of replacing electronic equipment in an average home is a whopping $8,000, and it may be even higher for homes in MD, DC, and VA. Whole-house surge protection is cheap insurance against electrical surges caused by lightning strikes. It provides a layer of protection to all the electronic items in your home.

To ensure complete safety, Kolb Electric recommends that you allow a qualified, experienced electrician to complete the wiring for whole-house surge protection—there are several steps involved that are best left to a professional.

If you require surge protection wiring or want a full whole-house surge protection installation, contact Kolb Electric.

Have you ever walked outside the house where your electric meter is mounted and heard a strange whirring noise? Was it the sound of the little hands on your frantically spinning around and around? If so, you were probably instantly alarmed. Every turn on that meter is costing you money. Your electric bill is going up right before your very eyes. How can you stop the wheels from spinning quite so fast? An electrician in Los Angeles is going to tell you how. At The Electric Connection we understand that every dollar counts and if you can keep a few more in your pocket things will be much better for you.

The following items are some of the biggest energy hogs in your home that are causing that meter to spin like crazy. Some you can control and others are just a part of life explains a Los Angeles electrician.

1-The refrigerator is costing you money. If you have invested in an energy efficient refrigerator, you are ahead of the game, but even those use a lot of electricity. The key is to make it use less by making sure the filter on the bottom and behind the refrigerator is clean.

2-A hot water heater is also going to cost you. You can limit how often it runs by shortening your hot showers and only washing full loads of dishes. Using the cold or warm setting on the washer is another way to cut back on hot water usage.

3-The air conditioning unit is probably one of the biggest culprits causing your meter to spin explains an electrician. Los Angeles residents definitely need to stay cool in the summer, but keeping the thermostat turned down too low isn’t really necessary. You can save some money on your electric bill by having a ceiling fan installed. The fan will circulate the cool air and create a slight breeze that makes you feel cooler.

Give The Electric Connection a call if you have any questions or would like to have a ceiling fan installed in your home.