Sometimes replacing a light switch or an outlet can be a quick job done in an afternoon. You may think looking up a ‘how to’ video on YouTube is all you need. But remember, electricity is dangerous and if you are not sure about what you are doing, it is better left to a professional. Here are a few troubleshooting tips to review before calling a professional electrician.

A common problem that can occur is circuit breaker tripping. If you find that power to certain parts of your home is constantly being shut off and requires you to use the circuit breaker to turn it back on, the line could be overloaded. Having to many appliances or electrical devices on one circuit can be too much for the line to handle and will cause the breaker to trip. To avoid this, try placing devices on a different circuit or unplugging appliances before you begin using another. If you continue to have problems you may have an issue with the circuit or one of your electrical devices. It may be best to call an electrician to diagnose the problem further.

Light bulbs must be replaced from time to time; it’s unavoidable. A common problem you could experience is dim or flickering bulbs. Turn off the power to the bulb and replace it with one you know is working properly. If the problem persists, there may be an issue with the socket or the wiring and it is best that an electrician takes a look at the problem.

While there are countless problems you can experience in your home, a good rule of thumb is to stay within your comfort zone. Everyone has a different level of knowledge about electrical systems but if a problem exceeds your understanding, it is best left to a professional. If you are unfamiliar with rewiring new sockets and switches, leave them alone and call an electrician. Tampering and altering wire connections can result in serious injury if not done properly. Be very cautious if you come across an exposed wire or are constantly being shocked, you could have a major safety issue on your hands. Make sure you shut off all power to the area or appliance you are unsure about and contact a professional.

An Indoor Generator™ is a backup power system that is delivered to you fully charged.  The charge is held in the unit’s batteries, which will be available for immediate use the moment you need it.  Everything that requires power from wall outlets will lose its power in the case of an outage.  You can either be left without power or you can implement your home back up power system to stay up and running without worry.

A unit like this is important for people who live in areas where outages and power surges are common.  Even if these occurrences are rare, maintaining power through an outage will provide safety and value in the event that you do lose power.  Also, if you live in a condo or high-rise where gas generators are not allowed, you can still use a battery-powered unit like the Indoor Generator.  Finally, if you have valuable computer or medical equipment, a power outage or surge could destroy them.  Thankfully, an Indoor Generator can prevent this.

Here are the reasons to hire a Dallas electrician for your backup power system installation:

In order to get the most out of your investment, you will want only the most reputable Dallas and Plano Electrician on the job.  Click on the link to find out about one near you.

This problem is similar to the heating appliance issue we started with.  Overloaded outlets are more than just a circuit-tripping annoyance, they can also become a danger quickly!  If you’re electrical panel is doing its job properly, the circuit breaker will trip before there’s a problem, but relying on a safety measure is not a safe practice.

Overloaded outlets are simply circuits that have too many things plugged into them.  This can happen by:

All of these practices can overload your outlets by putting too much demand on the circuit.  In a best case scenario, the circuit breaker trips.  The worst case leads to excess heat at the outlet, melting plugs and sockets or excess heat on the circuit which melts insulation from wiring in the walls, leading to a house fire.

Of course, even if you follow all of these protections, things can happen that are outside of your control.  That’s when your best defense is a strong safety net.  Early detection and warning for house fires is the best way to survive in an emergency.  The sooner you’re aware that there is a fire, the higher your likelihood of survival.  For the best defense:

A safety switch is essentially a device that very quickly switches-off the electricity in case any electrical fault is detected. In effect, it reduces the risk of injury & death caused by contact with electricity. Current day safety switches are very different from the ones used even up until a decade ago. Today, it’s mandatory to have these installed in buildings where any kind of electrical addition or upgrade has taken place.

Apart from this, safety switches are also needed for power outlets that that supply electricity to mobile homes like caravans etc. It’s not mandatory to have these safety switches in older homes; however, the recommendation is that you should consider getting them installed. It is one of the most effective ways to protect your family & yourself from electric shock.

ELCBs or Earth-leakage circuit breakers are safety devices used to prevent shock in electrical fixtures which have high Earth impedance. The current installations use the circuit breakers that directly detect leakage in current. Here are some features of an ELCB:

RCDs or RCCBs are essentially modern electrical wiring devices which quickly disconnect a circuit if they detect that there is an imbalance in the current between the energized conductor/s & the return conductor. They are designed to immediately switch-off the electricity supply when the electricity leaking to earth is detected to be at harmful levels. These devices offer very high levels of protection from electric shock.

Voltage Earth-leakage circuit breakers were first introduced around 60 years ago, while the current ELCBs were launched only around 40 years ago. For a very long time, voltage-operated ELCBs & differential current-operated ELCBs were both called ELCBs; this was because it was a far easier term to remember. However, as expected, this common name caused a significant amount of confusion within the electrical industry.

If someone accidently used the wrong one in a particular application, the installations may not get the kind of protection it needed. It was to eliminate this confusion that the International Electrotechnical Commission decided that the differential current-operated ELCBs will be termed as RCD (residual current devices). Any current that’s over & above the load current is referred to as the residual current.

ELCBs have a number of disadvantages such as:

Today the RCD is preferred means of providing effective shock protection. The term is also most widely used across the globe.

For more information about RCDs and the best electrical solutions, call Allround Electrical at 1300 169 263. You can also write to us at this email address. You may also reach us through this online contact form.

Thanks for reading,1300 169 263