By: Emilie Sims

Electrical outlets are found in nearly every room of the home, which represents a constant risk if you have small children. According to the National Fire Protection Agency, approximately 2,400 children each year suffer severe shocks and burns from inserting objects into the slots of electrical outlets. Additionally, there are an estimated six to 12 child fatalities each year related to this. Prevent this from happening to your family by childproofing the electrical outlets in each room of your home.

Also known as safe plates, these are additional covers that sit on top of your existing outlet and are held in place by a screw. There is a spring-loaded plastic cover that prevents your child from poking anything inside of the outlet.

Installing tamper resistant receptacles (TRRs) around the home provides a permanent solution to help reduce the risk of childhood shock and injury. TRRs, which look like ordinary outlets, are designed with small, spring-loaded receptacle plates that close off the slots, but open when equal pressure is applied to both sides. This design prevents children from inserting fingers or other foreign objects into the slots, and reduces risk of electrical shock or injury.

There are also several types of childproof electrical outlets that you can choose to install that will provide a permanent way to reduce risk of child injury.

This tamper-resistant outlet contains both a switch and an outlet to plug in devices. The dual mechanical shutter system blocks the insertion of objects into the outlet, increasing your child’s safety.

A ground fault circuit interrupter (GFCI) outlet can be identified by the “test” and “reset” buttons located on the receptacle. A GFCI outlet helps protect you from electrical hazards by shutting off the electricity circuit when it detects an imbalance. The National Electrical Code requires these outlets to be installed in water susceptible areas, such as the kitchen and bathroom. Test these outlets once a month to ensure they are working properly.

These receptacles look similar to standard ones, but the two outlets have the ability to spin 360 degrees. These outlets also allow you to use two large plugs at once.

Visit the Electrical Safety Foundation International and the National Fire Protection Association for more information on keeping your family safe around electrical outlets.

We offer photocontrol LED canopy lights for security lighting, parking garage lighting, gas station lighting, low-bay warehouse lighting, drive-thru lighting, and more. Using powerful LEDs, the light fixtures emit 9,000 lumens of bright natural white light.

The 100-watt LED canopy lights are equivalent replacements for 400-watt metal-halide (MH) fixtures but are designed to last three times longer. A photocontrol option is available to lengthen LED life span even further. The tork light-detecting sensors are designed to save energy by turning the light fixtures off during daytime hours. Shoppers can choose either a 120V AC or 208-277V AC tork sensor for the photocontrol fixtures.

These weatherproof LED lights are constructed of dark bronze die cast aluminum housings and shatterproof polycarbonate lenses. The LED canopy lights operate within a wide 90-277V AC range. Each surface-mount LED canopy light is equipped with a Mean Well constant-current driver as well as side and rear knock-outs that allow for various wiring options. A hassle-free five-year warranty fully protects against factory defects and malfunctions.

If you have questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

/foot)

Strips with more LEDs per foot will consume more power.

In short, if maximum energy efficiency is what’s most important to you, choose a light strip with smaller LEDs and fewer LEDs.

In order to ensure your LED power supply doesn’t overheat and fail prematurely, we use this general rule of thumb:

Make sure the total wattage of your LED strip lighting is at least 20 percent less than the power supply’s rated wattage.

For example, if you have an LED strip light that requires 80 watts of power to run, you’ll need a power supply that’s rated for at least 96 watts.

The vast majority of our strips include wattage per foot right on their product pages.

power supplies range from six watts to 1,500 watts for compatibility with a wide variety of LED strip lights.

Let’s take a look at an example:

It’s important to verify that the voltage of the power supply you choose is compatible with the voltage of your LED strip lighting. Also, be sure that the power supply’s input voltage matches that of the location it will be installed in. If you have an LED strip with 12-volt DC operation that you wish to use in a 120-volt AC home wiring system, you’ll need a power supply that includes 120 volts in its input range and has 12-volt DC output.

Another factor to take into account for longer runs is voltage drop. A significant voltage drop is present after a certain distance of LED strip. After this distance, there will not be enough voltage present to light the next length of strip. This varies depending on the type of strip and length being used. Usually, a single-density strip (nine or less LEDs per foot) will need to run back to a power source every 32 13/16 feet (10 meters). A high-density strip (18 or more LEDs per foot) will need to run back to a power source every 16 3/8 feet (5 meters). Please refer to “Max Run” in the specifications table of the strip light to determine how many can be run continuously without a parallel run back to power.

3) the 4) if you want your strip to be dimmable

power supply calculator on the product pages of all of our LED strip lights!

There are a few steps involved:

Step 1: Select your strip and the length you need.

Step 3: Click the green “Power Supply Calculator” tab, and select your product by choosing it from the list OR by pasting the exact part number in the search bar.

Step 4: Enter the number of strips at the desired length you’ve selected and voila! You’ll see a list of all compatible power supplies with the best match at the top of the list!

When dealing with electronics, safety is paramount, and you want everything to work like it’s supposed to. So if you’re still not sure which power supply to use for your LED strip lighting project, just reach out to our technical support team or customer service department at 866-590-3533. Our teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

Chances are that you must be one of those home owners who only looks at your circuit breakers when you happen to trip the circuit in your house and have to reset the switch to restore your power right? The truth is that a circuit breaker is actually a safety device rather than a simple on/off switch.