Are you living on the edge when it comes to fire safety in your home? You need more than a keen eye and a sharp nose to act quickly and avoid a Three Stooges re-enactment in the event of a fire in your home. With the help of smoke detectors, you can avoid any unnecessary antics, reduce fire risks, and increase your response time.

Do you need to invest in smoke detectors? Look for these 10 signs:

Don’t be a stooge. Stay on top of fire safety for the protection of your family and home. Contact Mr. Electric® today for the rapid installation of working smoke detectors on every level of your home.

If you’re in the midst of a renovation or simply rearranging your floor plan, then you’ve likely come across the need to add or relocate a light fixture. Maybe your new dining room table is a little wider than the old one, you’re adding a kitchen island with pendant lights, or you’ve finally convinced your significant other to let you get that pool table you’ve always wanted. In any case, you need to move or add a light fixture – but how and when?

First, it should be noted that, contrary to how it may seem, most light fixtures are not connected to a joist or even drilled into wood. Instead, hanging light fixtures and ceiling lights alike are located between joists and supported by electrical boxes that grip a wide surface area of the sheetrock that makes up your ceiling to support the weight of the fixture below; for heavier fixtures, like large chandeliers or ceiling fans, there are larger, even joist-secured boxes that will need to be used.

If you’re moving a light fixture, it is important to note that there are certain limitations as to where the fixture itself can go. If you wish to relocate the fixture to a place where a joist exists just above, then you’re likely going to have to use a swag hook and chain to anchor the fixture in place, as a box under a joist is not an option. That said, if you’re moving the housing for the fixture itself, you’ll need to know which direction the joists above run, then choose to move it either through the same joist cavity or drill through a joist to run the current wiring to the new housing. Other things to consider include which switch controls the light and where it is located, as it is a safe bet that a wire will have already crossed all joists above (at some point). This can prevent your electrician from drilling needlessly by allowing them to fish the wire back to the earlier point. If your switch is further away than the destination, you can bet they’ll have to do some drilling. Jumping through, between, and around the joists in the ceiling represents the largest obstacle your electrician (and light fixture) will face.

Once your location is set, all that is left is to get your electrician out to assess and perform the work for moving your box. If you’re planning on doing one large fixture over a pool table, island, or entire room, then you’ll want to take into account the power output of the fixture compared to what that circuit can safely allow for as well as the weight of the fixture. A typical rule of thumb is that anything under about 35 pounds can be handled by a standard drywall box, but something more (or with a fan) will need extra stabilization. Surprisingly, if you’re running numerous small pendant lights, the electrician may have an even easier time running the circuit and ensuring that your lights are up and running in no time. Just be sure to discuss the fixtures you have in mind with your electrician before you purchase them to know what they believe your limitations are!

Whenever you need electrical work done around your Des Moines home, contact the experienced professionals at Electrical Gurus. We are proud to offer the finest licensed local electricians in the area and are always more than happy to help out on your household projects.

There are numerous different ways in which an electrical fire can break out in the home and a number of ways to prevent it as well. Today, you will find there are a large number of electrical system protection devices on the market and this can make it a little difficult to decide which one will work best for your setting.

One effective installation you can use to prevent electrical fires in your home is an custom solutions to residential and commercial clients across Sydney.

You may not think about it often, but the power coming into your home travels a long way before it gets to your refrigerator, air conditioner, or any of the other appliances in your home. On the way, electrical current encounters fluxuations and interference from things like other appliances, machinery, and low quality wiring. That “Dirty” power can cause inefficiency and disturbance in your appliances, making things like the motors in your refrigerator and air conditioner, the circuits in your television, and all of your other electrical gadgets work harder than they need to, and wear out faster than they should.

A Power Conditioner will take the electrical current coming into your home and “clean” it, using filters to isolate power outlets and remove interference. This provides the correct voltage level to sensitive electrical equipment, allowing it to work safely and efficiently at the correct voltage.

Because power conditioners help your appliances run more efficiently, they can also lower the overall cost of running these appliances, and extend their lifespan. For more information about home power conditioners or for help on any electrical project in your home, please reach out to Dallas Electrician, ElectricMan Inc. by phone at 972-792-7270, or through the contact form on our website at www.electricmaninc.com