Other parts of the country may be warming up and getting ready to use our air conditioners, but we’re still relying on our heaters to get us through more than a few chilly nights. So if yours begins to malfunction, you may start to panic. This is understandable, but know that if you’ve had your system maintained before the heating season began, it may likely not even be an issue with the system itself.

Instead, you may be in need of Newton, MA electrical wiring services for some component of your heater. Keep reading to learn more about how your heater can be impacted by electrical issues.

This applies to both electrical furnaces as well as boilers. Both of these systems use heating elements—a set of coils that burn hot as a current passes through them—in order to raise the temperature of the air (furnaces) or water (boilers).

Both of these systems contain more than one heating element. Therefore, if you one fails you likely won’t lose your heat entirely, but your heater won’t be able to work as efficiently as it otherwise would.

If you’re utilizing a heat pump, then this is the most common electrical problem you might run into. Capacitors are cylindrical devices about the size of a soda can, responsible for sending electrical charges to the motors to start and keep them running.

Capacitors can burn out after years of use, or suffer from wiring issues, causing the heat pump to “hard start” (draining power) or quit functioning all together. You’ll need a professional to replace the damaged electrical capacitors.

Even if you have a heater that runs off of natural gas, oil, propane, or geothermal power, it’s going to have an electrical thermostat controlling it. Thermostats with failing wiring will begin to malfunction, often incorrectly registering your home’s temperature or failing to accurately set the heater. If your heater is failing to reach its target temperature with no other signs of a problem, your thermostat wiring could certainly be to blame.

What is a spotlight? What is a floodlight? Knowing the difference between the two is important for properly lighting any application. Before you can understand the difference, you must know what a beam pattern is. Beam angle or pattern is a measurement of the angles that are formed between a cone of light’s brightest point (the center) and the points on both sides of the center where the light’s intensity is 50 percent as bright.

PAR30 bulb that is available with a spot or flood beam pattern.

Fixtures, such as retrofit LED can lights may also look similar to one another while functioning as either spotlights or floodlights. Some light bars are even capable of emitting flood, spot, or combination beams. There are, however, certain fixtures that we imagine when we think of floodlights and spotlights.

Today’s infographic breaks down the essential facts about energy efficiency. It explains why energy efficiency is so important, and goes into detail about how wasting energy can harm the environment. Then, after convincing you that conserving power is a good idea, it offers a comprehensive guide to help you start saving more energy at home, assessing the efficacy of your appliances, insulation, and of course, your lighting.

I especially like this infographic for the Incandescent/CFL/LED comparison chart at the very bottom. Good stuff!

Have you ever turned on a light only to have it not work? Sure, we all have. Our first response is to turn off the switch and replace the bulb. But, what if the light still doesn’t work? Or what if the brand new bulb blows out as soon as you turn it on? This is a problem that may be one of your first signs of electrical trouble. Prior to the light going out for good, did it seem to be flickering? Outlets that have black marks around one of the prong holes or black anywhere around the outlet are definitely a cause for alarm.

Do not wait to see if the problem fixes itself, call an electrician. Beverly Hills homeowners can call The Electric Connection for an electrical inspection. It is always a good idea to have a complete electrical safety inspection to determine if the problem is isolated to one area or a major problem throughout the home. It could simply be an outlet with a loose wire or a faulty light fixture. In either event, the professional can take care of these quick fixes for you.

In more serious cases, especially in older homes, a complete wiring replacement may be needed. This is definitely a job for an electrician. Beverly Hills homeowners do not want to take any chances with their family’s safety.

Faulty wiring is a leading cause of home fires. You can help protect your investment as well as your family and all of those irreplaceable items in your home by getting a qualified electrician to do some troubleshooting. Identifying problem areas before they become a major catastrophe can save you a great deal of trouble, grief and money.

Not to mention, isn’t the peace of mind knowing your home is safe worth the call? Give the Electric Connection a call today and set  your mind at ease.