Rats and mice are quite common house pests; once they find your home to be a safe place to live in and that there are different sources of food there, they will be reluctant to leave. Not only do they pose a health hazard, they also tend to cause a lot of damage to various features on your property and will chew through the insulation of your electrical wiring.

This can affect the system and impact the supply of electricity throughout your property and can be a fire hazard as well. Here are some effective tips to prevent rodent damage to the electrical wiring in your home:

Since rodents are nocturnal creatures, you won’t really see them running around your home in the daytime. However, if you are wary, you will surely hear scratching and chewing sounds in the walls of your homes. You may also hear scurrying noises coming from the attic. You should look out for nesting material or droppings and will typically find these in enclosed spaces.

It’s important to check the wiring’s insulation with regularity to ensure that it’s intact and that it hasn’t been chewed by rodents. The unfortunate part is that this isn’t something you can do for wiring behind walls. However, if you are undertaking any repairs, renovation or upgrades, take that as an opportunity to check the wiring for signs of rodent damage.

If you notice any flickering or experience power fluctuation in a certain room or part of the house, or if you find that a certain circuit breaker keeps tripping for no specific reason, get the system checked for rodent damage.

If you notice any signs of a rodent infestation, it’s important that you act without delay and take some steps to get rid of them. Buy some spring traps and rat poison from your local hardware store and set these at different places where you have seen rat droppings or heard noises. Even as you do this, it’s equally important that you also identify where these pests are entering your property from. Place the bait or poison at these points along your home’s exterior walls.

If you find the infestation to be too severe or if you aren’t too confident about using DIY rodent control measures, call a licensed electrician to inspect the wiring and check it thoroughly for damage. If they confirm that the damage has been caused by rats, it’s a good idea to call pest control professionals to handle the rodent control for you. They will provide solutions and give you advice on the steps you can take to prevent these pests from entering your property.

While the rodent control professionals will ensure that the rats are eliminated from your property, they will also advise you on how to seal all the possible rodent entry points in your home. Aside from very evident points such as doors and open windows, these pests can easily squeeze their way into the indoor spaces of your property through holes and large cracks. If the cracks are too small, they won’t shy from chewing their way in through the loose concrete of the walls.

If you have noticed any rats or mice on your property, do not hesitate to call us to get the wiring checked. We handle all types of commercial and residential electrical installation, repair and upgrade jobs. For more information, contact the AllRound Electrical team at this number – 1300 169 263. Alternatively, you can write to us at our email address.

Thanks for reading,1300 169 263

Hopefully, you have surge protectors set up in your house to protect your electronics from power surges, or voltage spikes, that can fry your devices. Unfortunately, surge protectors won't save you from the evil cousin of a power surge -- a low voltage event, or brownout. Dimming lights in your house are a sign that you're experiencing a brownout, which over time can cause major damage to your appliances. 

Since your air conditioner is one of your most powerful appliances, any brief outage means it takes a lot of electricity to power the unit back up. To combat the problem, Direct Energy and One Hour Air Conditioning & Heating® offer the Comfort Sentry Contactor, a switching device with totally sealed contacts that goes in your AC unit. If voltage goes below a safe point or "flickers," the Contactor will automatically and safely turn the unit off — and then back on once the right amount of power is back. "In multiple dwellings, it will stagger turning power back on, one in 30 seconds, another in 5 minutes, and so on — to avoid using too much electricity all at once. It's protection built right into your home," explains Dave Borowski, spokesperson for Direct Energy. A smart homeowner will recognize this as an "ounce of prevention."

Electrical work is no joke. If left in the hands of an inexperienced or unqualified electrician, the results can be disastrous. Poor electrical work can leave you at risk of electrocution or electrical fire, and even if these issues don’t occur, it will still lead to ineffective operation. To prevent your breakers from tripping and your lights from flickering, among other things, you’ll want to do your research and make sure that the electrician you hire is the best for the job.

Hoffman Electrical has been providing electrical services throughout Florida since 1989. We can help you find an electrician in the St. Petersburg, FL area with the tips below!

The best electricians in St. Petersburg tend to share similar qualities. So when you’re doing your research, make sure you look for certain key qualifications. We recommend checking out the following:

When you’re looking for quality electrical work at an affordable price, call Hoffman Electrical. We proudly serve the St. Petersburg area, providing home and building owners with the best electricians for their specific needs and the most cost effective services. When you choose us as your St. Pete electrical company, you’ll receive:

This problem is similar to the heating appliance issue we started with.  Overloaded outlets are more than just a circuit-tripping annoyance, they can also become a danger quickly!  If you’re electrical panel is doing its job properly, the circuit breaker will trip before there’s a problem, but relying on a safety measure is not a safe practice.

Overloaded outlets are simply circuits that have too many things plugged into them.  This can happen by:

All of these practices can overload your outlets by putting too much demand on the circuit.  In a best case scenario, the circuit breaker trips.  The worst case leads to excess heat at the outlet, melting plugs and sockets or excess heat on the circuit which melts insulation from wiring in the walls, leading to a house fire.

Of course, even if you follow all of these protections, things can happen that are outside of your control.  That’s when your best defense is a strong safety net.  Early detection and warning for house fires is the best way to survive in an emergency.  The sooner you’re aware that there is a fire, the higher your likelihood of survival.  For the best defense: