Let’s face it—halogen and incandescent headlight bulbs are a thing of the past. fanless, driverless LED headlight bulbs were used in this installation.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points. Repeat these tape lines for your other headlight.

6. Remove your headlight assembly if necessary, remove the current bulbs, and install your new LED bulbs. Check your owner’s manual for specific instructions on how to replace your headlight bulbs.

7. Depending on your vehicle, you may have to adjust your headlight beam before or after the assembly has been reinstalled. Your owner’s manual will explain how to adjust the beams. Align each headlight so that the top edge of the beam is at the same height as your horizontal line(s). If your headlights can be adjusted horizontally or produce two light cutoff points, use the vertical tape lines to align them properly.

3. Shake the vehicle to ensure that your suspension system is settled. For more precise adjustments, inflate all tires to their designated psi capacity and have someone sit in the driver’s seat. Also, make sure that your vehicle’s gas tank is at least half full.

4. Measure from the ground to the center of your headlight assembly where the bulb is located. This step must be done for all vehicles. If your vehicle allows for horizontal headlight adjustments in addition to vertical adjustments, it’s important that you also measure the distance between the centers of both headlight bulbs. The vehicle featured in this video allows for vertical headlight adjustments only; therefore, center lines aren’t necessary but are shown for demonstration purposes.

5. Turn on your low-beam headlights. Using painter’s tape, mark your headlight measurements on a flat wall. Measure from the ground up, and apply a horizontal line of tape to the wall; this line represents the top of your headlight beam. You can either apply one long, continuous line or small sections where the brightest areas of the headlight beams are shown.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points.

There are always things that need to get done around the house. Some of those jobs tend to be more obvious than others. Things like repainting the walls, fixing the brick pathway or oiling squeaky door hinges tend to be more obvious. However, there are some little things that deserve our attention as well. Little things that are silent, but ignored or used improperly, they can become extremely dangerous. We are referring to the electrical outlets in the home. Little, insignificant and rarely focused on outlets pose a threat explains your Pasadena electrician. The team at The Electric Connection wants you to know you can help make your home a little safer by giving those outlets some well-deserved attention.

There are too many homes that do not have the GFCI outlets in the kitchen and bathroom areas. These outlets have been designed to trip the breaker within a split second of the circuit being interrupted. This one little feature can save lives by preventing electric shock. If you are not sure what the outlets are or whether you already have them or not, a quick visual will tell you the story explains an electrician in Pasadena. A GFCI outlet will have 2 small buttons in the center of the outlet between the top and bottom plug-ins. If the circuit is interrupted, you will want to unplug whatever device triggered the trip and push the reset button.

This one small feature is an important safety feature, especially when water is nearby, like the kitchen or bath areas. It is an inexpensive, quick upgrade that could save lives, prevent minor shocks and electrical shortages that could result in a fire. If you are ready to make this minor change, call your electrician. Pasadena homeowners will appreciate the additional safety precaution. Give The Electric Connection a call today and schedule your GFCI installation.

We had a call today from a customer. They were looking to retrofit their existing fixtures with LED. The competitor did a quote for them, and had recommended LED Post Tops as the retrofit bulb of choice for them. And this would have been a terrific solution if all their fixtures were acorn style pole mounted lights. But they weren’t, they were high bays, parking lot lights and show room lights. Yes. They are LED. Yes. They will save you money. But if you are trying to plow a field, you don’t buy a Porsche. You buy a tractor. The right vehicle for the job. And the same applies to LED.

First, let’s make sure we set the score right. We sell both. We sell LED Post Tops and we sell LED Retrofit Kits. We are not Post Top biased or Retrofit Kit biased. We even sell new fixtures. We have no biases! We want what is right for you!

contact our team and we’ll get back to you.

The best lighting jobs are the ones that aren’t noticeable. Have you ever walked into a room and just felt warm, comfortable and at home? It was probably the light placement and selection in the room that gave you that unforgettable feeling. With the right tools and tips in mind, you can also have that within each room of your home.

In order to effectively use your lighting to enhance your home’s décor, you must first consider the function of your room, the natural light source and the mood you are looking to achieve in your room. With this in mind, you can transform the look and feel of your home!

Knowing the function of your room will allow you to select the appropriate type of lights and placement in the room. For instance, a reading room will have soft lights with intentionally placed reading lamps whereas a kitchen will be a lot brighter and will be equipped with a number of task lights – each room can have very different functions therefore using different light sources and equipment.

Once you have determined the function for each room, you should then discover the natural or ambient light provided throughout the day. In the morning, afternoon and evening, take the time to turn off all your lights and see where the natural light source may come from and how it can be appropriately supported. You may have a street lamp right outside your living room that still provides a considerable amount of light, meaning you may not need to add as much light as you would have assumed for the evenings.

Lastly, you should determine the specific mood you are looking to achieve for your room. Romantic, bright, warm, calm, energetic – there is a number of different effects you could be searching for based on your room and décor. In a living room, we generally recommend a central light to add to the ambient light in the room and then use small accent lights to highlight main decorative objects in your room like a painting, mirror or even a plant.

With the function, natural light source and mood of your room in mind, you can transform your home with simple adjustments to your lighting. For more tips on how to improve the lighting of your home or to have a professional help with the installation, contact Expert Electric at 604-681-8338.