Our electrical system runs behind the walls and in our ceilings and floors. It is invisible, except for outlets and fixtures. Electricity is intrinsically counter-intuitive to think about. In fact, despite recent technological developments, we’ve only known how electricity works since the turn of the 20th century. So, you can be forgiven if even common residential electrics seem somewhat mysterious. Moreover, repairing these electrical systems requires the professional knowledge of a Kirkland electrician, who knows how to properly handle and harness electrical energy and run it safely through your home. In this post, we’d like to examine a few of the most common electrical repairs, so that you might be able to identify any problems and call for assistance.

As we transition into Fall and Winter, there will be plenty of new outdoor activities for everyone to enjoy. It is important to remember that, there will also be new challenges associated with outdoor electrical safety. The piling of up leaves and falling of snow can create unpredictable electrical hazards around the home. Keeping safe while outdoors doesn’t have to be complicated. Practice proper electrical safety by following these 4 Expert Electric outdoor electrical safety tips:

It’s always a good idea to semi-annually audit your home’s outdoor electrical equipment, especially in between Winter and Spring and then again in Summer and Fall. This ensures that your home is fully prepared to take on any electrical hazards that could occur during severe weather and temperature fluctuations. A licensed electrician can can easily complete this audit for you; however, it’s also possible to undertake this task on your own if preferable. During this audit, ensure that all outdoor electrical equipment is not only functioning properly also stored properly.

Loose or damaged electrical wiring can pose a serious electrical threat to your home, especially if it comes into contact with snow or leaves. A thorough inspection of all wiring and electrical cords should be completed and followed up with a replacement if necessary.

Melting snow can often result in large amounts of water pooling on the ground. If this water comes into contact with electrical equipment and wiring, the equipment and entire home can be at risk. It’s best to plan ahead and ensure that all electrical equipment, wiring and cords are placed and stored so that they won’t come into contact with water sources.

When in doubt, it’s best to contact your local licensed electrician to ensure that your home or building is safe from outdoor electrical dangers. The team at Expert Electric can inspect all of your outdoor electrical equipment and appliances such as hot tubs and pools, ensuring that all of the necessary outdoor electrical safety requirements are met.

Have any questions about outdoor electrical safety or and of our electrical services? Please fill out one of the forms on our website. We are happy to answer any questions you may have. The Expert Electric team of licensed electricians is here to ensure all of your outdoor projects are handled safely. Call us today at 604-681-8338.

Aluminum LED profile housings allow you to create customized light fixtures with LED strip lights. Our Klus brand LED channels are available in many different styles, including recessed-, or flexible, O-shaped, and more. Available in 1- and 2-meter lengths, the channels can be easily cut for any application from under-cabinet lighting and bookshelf lighting to showcase lighting and transition strip lighting. They’re available with a variety of lens options, such as clear, frosted, and etched that complete the profiles. We’ve put together a step-by-step guide for using these channels to create your own light fixtures. Please note that your specific channel might vary from the one used in this tutorial.

Materials needed:

1. With a pair of clippers, carefully clip through the clear plastic heat shrink as shown in figures A-C. You will want to take your time and be careful not to cut the strip’s wires while removing it.

2. Lay the LED strip into the channel, and position it along the bottom so that the ends of the strip and the channel are lined up (fig. A). Now, remove the paper from the strip’s adhesive backing (fig. B), and adhere the strip to the LED channel—starting at the lined end and working your way to the other end of the strip. Be sure to leave roughly 1/4-inch free at the end of the channel so that you can install the end cap as shown in figure C.

3. If one of your end caps doesn’t come with a pre-drilled hole, you will need to drill your own to allow the wires of the LED strip light to come through. In this case, we used a Dremel tool, but other options are viable as well. Regardless of the tool you choose, it is helpful to mark the end cap where you would like the wires to come through. Start the hole small, and increase the size as necessary.

4. Place the end cap on the wired side of the strip by threading the wires through the end cap as shown in figure A. Insert the end cap into the end of the light bar, and push firmly until it is fully in place (fig. B).

5. On the open end of the bar, slightly peel up the end of the LED strip (fig. A); this is necessary to install the end cap. Now measure your channel lens, and trim off the excess with clippers (fig. B). Be careful when trimming to avoid cracking the plastic. Excess material can be lightly sanded off. Once the lens has been cut to the proper length, slide it into the channel, and install the end cap as shown in figures C and D.

6. That’s it! Your customized LED light fixture is complete and ready for installation, which we will cover in the next step.

7. Mounting this LED profile is as easy as applying double-sided tape to the back of it and sticking it to your intended surface. Be sure to cut the tape to fit the back of the LED profile and to leave the tape backing on the side not attached to the channel until you are ready to mount it.

For most LED profiles, mounting clips are available for a more permanent installation.

If you have questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.