Motion sensor LED stair lights let you safely and effectively navigate your steps while eliminating the need for any action. And because they turn off automatically, they also save power! We’ve recently installed these handy little LED stair lights and wanted to share the process with you.

wire that will be needed. It is best to order more than you need so that there’s slack in the line and enough to extend to where your power supply will be mounted.

It’s important to choose the correct wire gauge for the length of wire you need and amount of current that will be flowing through it. The key is to avoid voltage drop, which happens when the supplied energy of a power source is reduced as electric current flows through wire (or any other pieces of equipment that do not supply voltage on a circuit). The longer the run of wire, the lower the gauge of wire needed.

*If you need help determining the correct wire gauge, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

3. Using wiring from the

4. Use a run of wire to join the PIR sensor at the top of your steps with the power supply. You can wire both PIR sensors to the power supply using electrical tape or with

5. Connect your main line to the PIR sensor at the bottom of your steps, and begin connecting each step light with

7. Finally, connect to power.

LED stair lights and

4. Connect your main line to the PIR sensor at the bottom of your steps, and begin connecting each step light with

6. Finally, plug the power supply into your wall outlet.

December is right around the corner and it looks like the temperature will continue to keep dropping. During this time of the year we all try to make our homes as comfortable as possible. Throwing on extra layers can help, but turning up the furnace is not always the best answer. If you want an efficient way to heat your home while also adding to the aesthetics of your room, an electrical fireplace is your best option.

Not only are electric fireplaces more eco-friendly than conventional gas and wood burning fireplaces, they are more economical. With their large heat output they cost just a fraction than what it costs to turn up the thermostat in your home. Additionally, electrical fireplaces require far less maintenance. You don’t need to worry about hauling around heavy wood or cleaning your chimney. With an electrical fireplace you just need to dust and clean the glass from time to time.

Because there is no real flame in an electrical fireplace, there is no need to worry about having the right connections to install the fireplace. You can install one virtually anywhere in your home. With the help of an expert electrician, we can run the electrical lines that are needed and make sure that everything is hooked up correctly.

The great thing about electrical fireplaces is that they come in a wide range of styles and designs. There are several types of electrical fireplaces:

You know that little meter outside your home that is fairly unattractive and unnoticeable until you hear it making a scary sound. The sound is the little dial spinning around and around. That dial spinning represents your money flying out the door. The dial is measuring the amount of electricity you are using in your house. A spinning meter can be a little scary and you will be dreading the next electric bill. When you think about this summer, it is easy to really get concerned about how much it will cost you to keep your home cool. An electrician in Glendale can help you manage your spinning meter and help keep some of that money in your pocket. The team at The Electric Connection is here to help.

These are 5 ways you can help limit your electricity usage and keep your electric bill down.

1-Make a commitment to set your thermostat at about 74 this summer. That is a comfortable temperature and you can maximize it by using a ceiling fan installed by a Glendale electrician to help stir up a breeze and circulate the cool air.

2-Buy a laundry rack and dry a few things outside on the patio to cut down on how often you use the dryer.

3-Be more conscientious about the amount of hot water you use. Don’t leave the faucet running while you wipe down cupboards or rinse dishes. Shave a few minutes off your shower time as well.

4-Switch out your old bulbs for the much more energy friendly LEDs. These tiny little bulbs use a fraction of the electricity of the standard bulb. You can also use CFLs. In some cases, you will need to have your light fixtures upgraded by an electrician. Glendale homeowners will appreciate the new look an updated fixture brings to a room.

5-Buy new curtains and blinds to use as sun shields this summer. It will help keep your home warmer and save on cooling costs.

Give The Electric Connection a call today to install that new light fixture or ceiling fan so you can start saving money on your electric bill.

Let’s face it—halogen and incandescent headlight bulbs are a thing of the past. fanless, driverless LED headlight bulbs were used in this installation.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points. Repeat these tape lines for your other headlight.

6. Remove your headlight assembly if necessary, remove the current bulbs, and install your new LED bulbs. Check your owner’s manual for specific instructions on how to replace your headlight bulbs.

7. Depending on your vehicle, you may have to adjust your headlight beam before or after the assembly has been reinstalled. Your owner’s manual will explain how to adjust the beams. Align each headlight so that the top edge of the beam is at the same height as your horizontal line(s). If your headlights can be adjusted horizontally or produce two light cutoff points, use the vertical tape lines to align them properly.

3. Shake the vehicle to ensure that your suspension system is settled. For more precise adjustments, inflate all tires to their designated psi capacity and have someone sit in the driver’s seat. Also, make sure that your vehicle’s gas tank is at least half full.

4. Measure from the ground to the center of your headlight assembly where the bulb is located. This step must be done for all vehicles. If your vehicle allows for horizontal headlight adjustments in addition to vertical adjustments, it’s important that you also measure the distance between the centers of both headlight bulbs. The vehicle featured in this video allows for vertical headlight adjustments only; therefore, center lines aren’t necessary but are shown for demonstration purposes.

5. Turn on your low-beam headlights. Using painter’s tape, mark your headlight measurements on a flat wall. Measure from the ground up, and apply a horizontal line of tape to the wall; this line represents the top of your headlight beam. You can either apply one long, continuous line or small sections where the brightest areas of the headlight beams are shown.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points.