“Truth will ultimately prevail where there is pains taken to bring it to light.”—George Washington

Just in time for President’s Day, exclusive designs from Maxim Lighting and ET2 bring the truth to light with innovative illumination backed by 40 years of quality craftsmanship and service.  Whether you are searching for subdued elegance for the dining room and powder room or plentiful task illumination for the kitchen and office, look to Maxim  lighting fixtures for pure and trustworthy constitution.

Capitol Lighting is proud to present the finest in home lighting and accessories with promotional values on the latest from Maxim Lighting and ET2, including:

Enjoy holiday savings on all Maxim lighting fixtures and ET2 in honor of President’s Day, and take 10% off all kitchen pendants too!

constant-current LED driver or constant-current driver is used to regulate the amount of current that is supplied to an LED or LED array to maximize LED lifetime. If current is not regulated, LED brightness can fluctuate and life span can be shortened. The constant-current driver is used for LEDs or light fixtures that require a stable output current and operate within a range of voltages. Most finished LED products already have a constant-current driver or resistors to regulate current. If you’re building an LED fixture or replacing a constant-current driver, it’s important to verify that the output current and voltage of the driver is compatible with the LEDs’ current and voltage. If your LED product already has a constant-current driver or uses resistors in the LED array, you might need a constant-voltage power supply.

If your LEDs are dimmable and you want to change their brightness, choose a Magnitude Dimmable Power Supplies. These dimmable power supplies work by varying the power on the AC input side of the power supply by means of a TRIAC dimmer. This change in power on the AC input side will vary the voltage on the DC output side and control the intensity of the LEDs. TRIAC dimmers are common hardware store and household dimmers, which include brand names such as Lutron and Leviton.

Pulse-Width Modulation Dimming: Pulse-width modulation (PWM) dimming can be used to control dimmable power supplies such as Mean Well LPF Series. This type of dimming control adjusts the output current based on the duty cycle. As the duty cycle increases, current will increase and the LEDs will be brighter. Conversely, if the duty cycle decreases, the current will decrease and the LEDs will be dimmer. Pulse-width modulation for these drivers is based on a 10-volt signal level with a frequency between 100Hz-3KHz. The MLD-5A are compatible for this application.

Resistive Dimming: Resistive dimming can be used to control dimmable power supplies such as 12-Volt Mean Well HLG-40-240 Series or 12-Volt Mean Well HLG-600 Series or here.

The efficiency of a power supply or driver indicates the percentage of power that goes toward making your LED product function. An efficiency of 80 percent or higher is recommended for operating LEDs. 

When choosing a driver or power supply, the size of an LED product’s housing or area of installation is important. If you wish to put a constant-current LED driver inside of a product, the driver must be small enough to fit in the product’s housing. Similarly, if the driver or power supply is used outside of the product’s housing, it should fit the area of installation. Drivers and power supplies are available in a variety of sizes to suit your needs.

A Class 2 driver or power supply is in accordance with limited power levels defined by the National Electric Code (NEC) and fulfills the requirements of Standard UL 1310. Output is limited to 60 volts DC and 100 watts. Because power sources with this rating have limited output, it might not be possible to power as many LEDs or lights as those that don’t have a Class 2 rating. However, these power supplies and drivers provide protection from fire and electric shock.

A Class II rating refers to a double insulation layer between AC input and DC output wires. These drivers and power supplies do not require a ground connection.

If you recently had a pole building or shop put up on your property, you are probably debating to have it powered with electricity or stick with a generator. There are clearly some real benefits to a shop having electricity. If you are simply using the building to store items, than electricity is probably not a major concern. However, if you are planning to use your shop to work on various hobbies or use it to repair vehicles, electricity is extremely helpful. You will need a Burbank electrician to go about completing the wiring process. You can depend on the team at The Electric Connection to help you make your shop complete with electricity.

Depending on the amount of electricity you need in your shop, you may need to have a sub-panel installed. This is something your electrician will discuss with you and advise you on. If your home is already using the majority of the breakers available in your existing panel, you will need an upgrade or an additional panel installed to run the shop. The size and type of the tools you will use in the shop will influence your decision.

Once you have decided on the electric panel situation, the next stop is to discuss outlet placement with your electrician. Burbank shop owners can decide how many outlets they need in the shop. You may even need a 240-volt outlet to run certain heavy machinery or to plug in a Level II electric car charging station. These are all options for you to consider when you make the decision to hire an electrician. Lighting is yet another element you will want to think about. Typically, a single fixture is installed along the ceiling and then several lamps will be used to illuminate specific work areas. If you would like to discuss running electricity to your new shop, give The Electric Connection a call today.