RGB LED strip lights are a great way to add a pop of color to your above-ground pool. These low-voltage LED lights can be applied to the inside rim of your pool or around your pool deck. With RGB LED strip lights, you can choose from a ton of dynamic color-changing and single-color modes with adjustable brightness and speed control. They’re great for parties or late-night swims and can be easily installed. We’ve included installation instructions for our waterproof LED strip lights. Some cities require above-ground pool lighting to meet National Electrical Code (NEC) Article 680 standards, which would limit possible pool lighting installation locations. Before you purchase LED pool lights, check your city’s code requirements. We also recommend that you have a certified electrician install your lights.

1) Before ordering your LED strip lights, measure the diameter of your pool and multiply by 3.14 to find its circumference; this number indicates the total length of strip that you will need. The 21-foot pool used for these installation instructions has a circumference of 65.94 feet and requires 4 runs of 16-foot LED strips.

You will also need to measure the distance between where your power supply will be and both sides of your pool where the amplifiers will be installed (see the setup and wiring illustration below). These distances will tell you how much 18-gauge wire you’ll need for connecting the amplifiers to power. Make sure to account for the distance of any dips or turns that the wires may take along their paths.

Lastly, measure the approximate distance that will be between your controller and where your strip lights begin. This distance will tell you how much 22-gauge wire you’ll need for connecting the controller to your strips. You will also need two small sections of this wire for connecting your first and second strip lights to the amplifiers.

2) Before you’re ready to install your LED strip lights, be sure to drain your pool. Begin by creating or locating a dry area away from your pool for the power supply. The power supply should be contained in a weatherproof box. Power supplies should be installed between a ground fault circuit interrupter (GFCI) protected circuit and the pool’s junction box. It’s crucial to use a GFCI protected circuit as it shuts off if current flows where it’s not supposed to.

Wire the included plug to the power supply, but do not connect to power until the installation is complete.

3) Connect your RGB LED controller to the power supply. Cut the barrel off of the controller wiring. Strip back the remaining wires, and connect its wires to the power supply.

4) Cut the LC2 connector off of the remaining end of the controller, and strip back the wires. Run 22-gauge four-conductor wire to connect the controller to your low-voltage pool lights; use dolphin connectors to join like-colored wires. Connect your first two LED strip lights to the controller by joining each set of like-colored wire with a dolphin connector. You should be connecting four wires of each color (red, blue, green, and black) together. For added protection, cover all wire connections in this installation with electrical tape.

5) You will apply strip 1 clockwise around your pool rim and strip 2 counterclockwise. If you have a flat surface, use mounting clips to secure the strips in place as you go. If you want to mount the strips under your pool rim, drill small holes in the trusses approximately every 2 feet. Use cable ties to anchor the strip to the truss. You can also use speed nuts or cotter pins for strip anchoring to avoid drilling holes.

Solder a small section of 22-gauge four-conductor wire onto the strip’s end terminals. To reseal the LED pool light strip, slide wires through the holes of a 10-mm end cap, fill the cap with silicone, and slide it into place on the end of the strip. Be sure to cover all of the exposed conductive traces to ensure water resistance. Allow a minimum of two to three hours for the sealant to cure.

7) Once the new end wires are attached to the strip, you will mount the amplifier. Use the double-sided 3M foam pad to mount the amplifier in the middle of strip 1 and strip 3. For best results and added security, apply 3M adhesion promoter to the amplifier and its installation location on the pool wall.

8) Using a dolphin connector, join each like-colored wire on strip 1 to the same color on one end of the amplifier. Do the same when connecting strip 3 to the other side of the amplifier. You should be connecting three wires in each color (red, blue, and green) together on each side of the amplifier. The black strip wire will be joined with white amplifier wire. Note that the separate group of just black and red wires are meant to be connected to the power supply. Follow the same instructions for connecting strips 2 and 4 to the amplifier on the other side of the pool.

9) Use 18-gauge wire and dolphin connectors to connect the amplifiers to your power supply.

10) Plug the power supply’s attached cord into an outlet, and enjoy your LED pool lighting system! Refill your pool with water, but make sure to leave space between the water line and the lights.

For more LED pool lighting options, see our entire selection of waterproof color-changing LED strip lights.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

If you are thinking about beating the heat this summer with a new pool in your backyard, you will need to hire an electrician in Pasadena to complete the wiring. A new pool is an exciting toy that will lead to hours of fun for the whole family and of course, family friends. There are plenty of tools needed to keep your pool clean and safe to use. Tools like filters, pumps and heaters if desired, all require electricity. Water and electricity do not mix so it is important an experienced electrician, like those at The Electric Connection, complete the wiring for the pool to ensure it is safe. Even if you are choosing to go with an above ground pool, there is still some electrical that will be needed to operate the filter and pump.

The following are some of the things that will need to be addressed when bringing your pool up to Pasadena electrical codes.

*Depth of the wiring must be buried at least 18 inches for PVC conduit or 6 inches deep for EMT conduit. Your electrician can discuss this in more detail with you.

*Your pool will need a dedicated breaker and outlets to run on. The outlet needs to be no closer than 6 foot from the pool’s edge and no farther than 20 feet from the pool. This is the receptacle that will be used to power your filtration system, pump, heater and an automatic pool cover if you choose.

*Lighting inside the pool and around the pool area will also need to be installed by an electrician.

If you home’s electric panel is already maxed out, you may need to have a sub-panel installed to run the various equipment needed to keep your pool in tip-top condition. Give The Electric Connection a call and schedule an appointment to discuss your pool installation needs.