Older homes have a very distinctive look and feel and some people prefer to invest in older properties, rather than in a newer one. These homes have an old world charm and offer great value too. But most of these homes also have older installations and some basic upgrades and improvements can give them a new lease of life.

While most property owners do get the house painted, add new features and furniture etc. very few consider getting the extension cord doesn’t have the capacity to power multiple devices simultaneously. The safest thing to do is to get more powerpoints installed at the time you get the rewiring done. When you are planning this installation, take into account the number of appliances used in your home and get that number of (or more) power points fitted in the different rooms.

You may have heard the term GFCI from your electrician before. But what exactly does it mean? And is that type of outlet really necessary in your home or building?

We all know that water and electricity don’t mix. That’s what makes electrical outlets in kitchens, bathrooms, and other rooms where water is used so tricky. To reduce the chance of electrocutions, burns, and shocks, virtually all North American building codes require that ground fault circuit interrupter outlets (GFCIs) be installed where there is water nearby. GFCI outlets have a built-in circuit breaker that instantly stops the flow of electricity when it senses a surge.

A GFCI outlet not only helps keep you and your family or building occupants from getting shocks and burns, but it helps prevent electrical fires. In the even that there is an electrical fire, it can lessen the severity and any damage.

A GFCI outlet is important not only to meeting local building code requirements, but also to help prevent potentially-fatal accidents.

GFCI outlets are designed with a red button that activates the outlet after the built-in breaker is tripped, and a black button that tests the outlet to make sure that the breaker is working properly. The U.S. Consumer Product Safety Commission (CPSC) recommends that all ground-fault circuit interrupter outlets be tested in the following intervals:

To test your ground-fault circuit interrupter outlets, plug a lamp into the outlet. Turn the lamp on and push the black test button. If the lamp goes out, the outlet is working properly. If the lamp remains lit, contact a licensed electrician to evaluate the problem. Electrical and wiring issues make poor DIY projects and are best left to electricians who are trained to safely handle electrical current and wiring.

At Kolb Electric, we want to help you keep your home or building safe in the Maryland, Northern Virginia, and Washington, DC areas. We can save you time by inspecting and testing all of the ground-fault circuit interrupter outlets in your interior space and addressing any electrical issues we may discover during the tests. To learn more about electrical safety and GFCI outlets and/or to schedule a service appointment, call us at 877 287-1179. We’ve been helping Mid-Atlantic homeowners like you with their electrical needs since 1925.

Whether you’re doing industrial wiring or residential wiring for electricity, you’ve got a complex task ahead of you. Needless to say, industrial wiring is essentially a much more complex form of residential wiring. This article will assume that you have some elemental electrical wiring knowledge or aptitude, and it will simply provide you with a very basic overview of what you need to understand with regard to residential wiring and industrial wiring.

It will be up to you to look up your local building and electrical codes for your home or office space. Also, check your local laws to see if you are even permitted to do your own amateur wiring before you proceed. Above all things, approach any wiring project with this knowledge at the forefront of your mind: “electricity can be deadly.” Put your safety ahead of all other concerns.

Red wires and black wires are usually “hot”. This means that there is a current (amps) flowing from the circuit breaker to the electrical box or the appliance in question.

The white wires usually are “returns”. This means that they allow current (amps) to flow back to the circuit breaker after the electricity has passed through the load or appliance in question.

White wires should not be connected together with ground wires, with the exception being back at the circuit panel bus bar. If you fail to observe this rule, then every single time the load is energized (such as turning on an appliance), electricity will flow through the ground wire and the return wire simultaneously. This is very dangerous.

A ground wire is usually bare and attaches to an appliance’s frame. Under normal circumstances, current should not be passing through it. Only when there is a short circuit should electricity pass through the ground wire; this happens so that the circuit breaker will kill the flow of current to the site or appliance.

Smart industrial wiring is based on 3-phase electrical power. 3-phase electric allows less workload to be placed on each wire involved while at once allowing them to work together to give you maximum results. With 3-phase electric, the wires are smaller and the motor is smaller than a typical single-phase motor. These factors allow greater efficiency and longer lasting motors and wires.

There are four types of 3-phase electrical power:

No matter which type of 3-phase electrical power you choose to use, you’ll need a voltage meter in order to determine the actual voltages that are available to you. The type does not determine this.

Industrial wiring typically runs through metal conduits, armored cable, or a raceway. These enclosures are the safety ground–never the neutral wire.

The above information should give you a nice guidepost for doing more research into and getting more practice with either residential wiring or industrial wiring. Again, safety comes first!

It’s incredible the way lighting can change outdoor spaces. As is the case with indoor spaces, spending comparatively little on lighting can produce dramatic results. A DIY outdoor lighting project might be just the thing to make you fall in love with your home all over again. But before you begin an outdoor lighting project, it’s important to think about your options. Here are 10 tips for 10 approaches to outdoor lighting.

1. Using Outdoor String Lights

Outdoor string lights are just great. But there are so many different kinds! Some have bare bulbs; some have lanterns. Some are LED; some incandescent. Some are white; some are colored. Make sure you research your options and choose the ones that are right for YOU!

2. Taking DIY Outdoor Lighting to the Next Level

Sure, you can install a standard low voltage lighting fixture and be justified when you say you Did It Yourself, but have you ever considered making your own DIY outdoor lighting fixtures? Mason jars seem to be the ingredient of choice when constructing your own outdoor lights. The internet is full of instructions for making DIY outdoor lighting fixtures, so do your homework and find the perfect project to make your outdoor area more luminous.

3 . Making it Modern

Let’s get weird! Isn’t that what modern outdoor lighting seems to say? I guess it depends on whom you ask. Modern outdoor lighting usually consists of interesting light fixtures with unusual, playful designs, and they can really make your outdoor vibe more interesting and thought-provoking.

4. Showing Off Textures

Sometimes you start with a particular light source in mind. These days, that light source is often LED. If you’re sure you want to use outdoor LED lights, you have a wide variety of outdoor LED light fixture types, from LED rope to LED tape to LED path lights, step lights, puck lights, recessed lights, and string lights. LED outdoor lights are highly efficient and look great. And some, like the one above, run on solar power! That means free!

8. Decking Out the Deck

If you are focused specifically on outdoor deck lighting, make sure you think about caution. Outdoor deck lighting should entail step lights if there are steps and should include lights around the perimeter of the deck. LED tape or rope, colored or white, are often great for running on the underside of deck railings.

9. Using Timers