Why is a bad GFCI outlet such a big deal? To put it simply, they exist to protect you from electrical shock. As required by electrical code, these outlets are in places within your house where there is an increased risk of electrocution. These include bathrooms, kitchens or outside (wherever water is likely to be present).

GFCI outlets come with a sensor designed to identify changes in current, which can indicate unsafe conditions or the risk of shock. There’s a breaker inside the outlet, which trips when there is a surge in current. This shuts down the power supplied to the outlet and any connected outlets, protecting you from electrical shocks.

GFCIs come with two buttons on them (usually black and red), with one serving to test the outlet and the other for resetting it after the breaker inside has tripped. A bad GFCI is a serious problem, as they are too important for you to ignore them for any amount of time. It is, therefore, crucial that you stay aware of when you might have an issue with one of yours.

In the majority of cases, a GFCI outlet protects you by not providing power. If there is an issue with an appliance plugged into it, the power would likely cut off long before you even get the chance to use it. When this happens, it can be easy to assume there’s something wrong with the outlet itself. But in many cases, its breaker tripped for a good reason. GFCIs are also designed to shut themselves off in the event of a person getting shocked, which isn’t always easy for it to determine with much accuracy. In other words, your GFCI outlet breaker might trip when you’re not actually in any danger.

The GFCI detects current that branches off from the intended circuit, even if the branches are small and harmless. This can include instances of a wire making contact with another component of the receptacle, which can be completely innocent. When the cause of a trip is a passing occurrence, you should be able to reset the outlet breaker with a simple push of the correct button.

Outlets can get worn out and lose some of their effectiveness over time. This also applies to GFCIs. If your GFCI outlet is tripping much more frequently than it should, it could mean it’s nearing the end of its lifespan. This is due to GFCI outlets losing the ability to adjust to changes in current as effectively as they used to. The result is that trips begin occurring for reasons that were never a problem in the past.

If your outlet breaker is tripping every time you use a hair dryer, and it never did that before, it’s a sure sign you have a bad GFCI outlet. If this becomes the case, it’s important to get it replaced as soon as possible! These outlets are too crucial a safety measure for you to delay on getting a new, functional one.

Rats and mice are quite common house pests; once they find your home to be a safe place to live in and that there are different sources of food there, they will be reluctant to leave. Not only do they pose a health hazard, they also tend to cause a lot of damage to various features on your property and will chew through the insulation of your electrical wiring.

This can affect the system and impact the supply of electricity throughout your property and can be a fire hazard as well. Here are some effective tips to prevent rodent damage to the electrical wiring in your home:

Since rodents are nocturnal creatures, you won’t really see them running around your home in the daytime. However, if you are wary, you will surely hear scratching and chewing sounds in the walls of your homes. You may also hear scurrying noises coming from the attic. You should look out for nesting material or droppings and will typically find these in enclosed spaces.

It’s important to check the wiring’s insulation with regularity to ensure that it’s intact and that it hasn’t been chewed by rodents. The unfortunate part is that this isn’t something you can do for wiring behind walls. However, if you are undertaking any repairs, renovation or upgrades, take that as an opportunity to check the wiring for signs of rodent damage.

If you notice any flickering or experience power fluctuation in a certain room or part of the house, or if you find that a certain circuit breaker keeps tripping for no specific reason, get the system checked for rodent damage.

If you notice any signs of a rodent infestation, it’s important that you act without delay and take some steps to get rid of them. Buy some spring traps and rat poison from your local hardware store and set these at different places where you have seen rat droppings or heard noises. Even as you do this, it’s equally important that you also identify where these pests are entering your property from. Place the bait or poison at these points along your home’s exterior walls.

If you find the infestation to be too severe or if you aren’t too confident about using DIY rodent control measures, call a licensed electrician to inspect the wiring and check it thoroughly for damage. If they confirm that the damage has been caused by rats, it’s a good idea to call pest control professionals to handle the rodent control for you. They will provide solutions and give you advice on the steps you can take to prevent these pests from entering your property.

While the rodent control professionals will ensure that the rats are eliminated from your property, they will also advise you on how to seal all the possible rodent entry points in your home. Aside from very evident points such as doors and open windows, these pests can easily squeeze their way into the indoor spaces of your property through holes and large cracks. If the cracks are too small, they won’t shy from chewing their way in through the loose concrete of the walls.

Over the last few years, talk about LED lights has become more commonplace. As there is a global trend to become more economically friendly, it is no surprise that more people are switching to LED lights. LED lights, which stand for ‘light emitting diodes’, are not only ecologically sound, but economical as well.

Traditional fluorescent lights contain small amounts of mercury. Mercury is extremely hazardous to the environment but humans as well. If you come into contact or inhale mercury, it can be very dangerous and negatively impact your health. Fluorescent bulbs need special care to dispose of properly. LED lights do not contain any hazardous or poisonous material and are 100% recyclable. This means you can have peace of mind when disposing of your LED bulbs and know that the impact on the earth is minimal.

When we say energy efficient, this means that it takes less electricity to convert into light. Part of the reasons that LED bulbs are more efficient is because they do not heat up as much. Less energy is lost in heat so the electrical energy that flows in can go directly to light. Traditional bulbs tend to run at 20% efficiency where as LED bulbs can run at 80% efficiency. Practically speaking, if you are using LED bulbs in your home you are looking at large saving increases on your monthly electrical bill!

In addition to saving money on your monthly electrical bill, you will also save money by replacing your light bulbs less frequently. Standard light bulbs have a life span of 800 to 1,500 hours, while fluorescent bulbs can last up to 10,000 hours. LEDs on the other hand can last up to 60,000 hours! You can run for years without needing to replace an LED bulb. So while LEDs are more expensive initially, they are a wise investment in the long run.

Although the number of benefits of using LED lights is quite long, these are just a small number of ways that LED bulbs help the environment and your pocketbook.

Electrical rewiring in Fairfax, VA may be the best decision you make this spring. After all, with the weather finally making the switch from snow and sleet to sun and heat, now is the time to start making some positive changes around your home. There’s no better way to start changing with the times than by improving your home’s electricity and with improved rewiring, you can live more comfortably in your home than ever before!