If you’re tired of shelling out a crazy amount to the energy company each and every month, then maybe it’s time to look at how your household is consuming power and improve the efficiency of your usage. To help with that, our Top Rated Local® Des Moines electricians have committed to taking calls and appointments specifically for improved energy efficiency.

If your energy bill is high, then there is a really great chance that your break-even point will be very low. In case you’re not one of the many financial experts that call Des Moines home, a break-even point is essentially just an investment term that is used to calculate the potential risk of a course of action compared to its likely reward; this means that the break-even point for your investment in optimization will be achieved through reduced monthly energy costs + any local or federal subsidies the improvements qualify you for – the costs of installation or upgrading. Costs, in this case, can be both financial and temporal, meaning that your savings need to rack up quickly to account for the time and money you’ll invest up front. The good news is this: Many new homes (built in the last 5 years) can be drastically upgraded and optimized, and just about all below that line (older than 5 years) will see an even more dramatic improvement.

When power reaches your home, it inevitably is routed to and through an electrical panel; this panel determines much of your home’s energy efficiency before anything is even turned on. From the electrical panel to the wiring and outlets themselves, the amount of upgrades and optimizations that can be done for a comparable cost to the original outdated panel that dramatically reduce energy waste are dizzying. From the smallest changes, such as installing energy-efficient lighting or new outlets, to full-scale electrical overhauls, the potential for savings are really multiplicative.

Our electricians come into the picture by offering the tools and experience necessary to quickly and effectively route out outdated and inefficient systems and find the optimal solution for improving your home’s flow of energy. In as little as a few minutes, our electricians can make pointed suggestions that can and will save you substantially on your energy bills or find nothing noteworthy enough to justify the cost based upon the break-even point. At Electrical Gurus, we believe in offering this service to optimize your systems to make them safer and save you money, not add on an unnecessary expense.

Get in touch with the master electricians at Electrical Gurus for an expert opinion on what can be done to reduce your home’s energy costs. We are proud to serve the entire Des Moines area with both residential and commercial electrician services; contact us today to put those skill to work for you!

As a Dallas Electrician with over 27 years of experience, ElectricMan Inc. has seen many of the dangers of DIY Electrical first hand, and has often been called in to make repairs after a DIY home improvement project has gone wrong, or the home owner realized that they were in over their head. The experience to take on any electrical home improvement project is something that is obtained by years of professional training and experience under a Licensed Master Electrician. That kind of experience isn’t something that the average Do-It-Yourselfer has, even if you do consider yourself a Jack-Of-All Trades.

One of the biggest dangers of DIY Electrical work is simply the fact that electricity can be deadly when not handled properly. Many DIY home improvement projects are often done in a hurry, and without proper planning. Something as simple as forgetting to switch off the breaker, using the wrong tools for the job, or even accidentally brushing up against the wrong wire can send high voltage coursing through a human body, easily causing burns, ventricular fibrillation (uncontrolled movement of the heart muscles), and death. We are so accustomed to being able to flip a switch and use electricity in our daily life that we often forgot how powerful it truly is.

One of the major causes for DIY Electrical accidents is unfamiliarity with the electrical circuits in your home. Due to shoddy electrical workmanship in many older homes, it is often difficult to tell which outlets, appliances, and lighting fixtures are on a given circuit, especially if your breaker box was improperly labeled, or if the labeling has faded over time. Most home owners will simply switch off breakers until they see the lights turn off in the area that they will be working, and assume it is safe to start working. This is an incredibly dangerous practice since it is not always the case that all outlets and lighting fixtures in an area will be on the same circuit. A Licensed Dallas Electrician will be familiar with standard wiring practices and will know the proper way to test the circuit that they will be working on to ensure that it is safe.

Another huge benefit to using a licensed electrician for your home electrical work is that they will be well versed in all of the building and safety codes required to make sure the job is done right. The reason that this is important is two-fold. First, it is legally required to adhere to all building and safety codes, and if you ever intend on selling your home or having it inspected for any other reason, a DIY Electrical repair or addition will cause your home to fail inspection if building and safety codes are not followed to the letter, generally costing you more money later down the line to have an improperly performed job repaired. Secondly, and even more important, is the fact that building and safety codes are put in place for a reason. If you are not familiar with these codes or do not follow them, you are putting yourself and your family at risk of electrical shock, electrical fires, and injury or death due to a faulty repair.

A reliable Licensed Dallas Electrician such as ElectricMan Inc. will ensure that any home improvement project involving electricity in your home is completed correctly, in compliance with all of the proper safety and building codes, and will guarantee their work to ensure a successful outcome, and the safety of you and your family. If you would like to learn more about the capabilities and experience of ElectricMan Inc. or discuss a project or repair that you are planning for your home, reach out to us today by phone at 972-792-7270, or visit us at our website at www.electricmaninc.com!

By providing early warning in the event of fire, smoke detectors can allow you and your family sufficient time to reach safety. Experts report that you can increase your chances of surviving in a home fire by 50% simply by having smoke detectors. Click here for more information about installing  smoke detectors in Los Angeles, my electrical company’s service area.

If your house was built before 1950, it likely has electrical wires with cloth insulation. Over time, the cloth dries out and becomes brittle. Eventually, it crumbles off the wire, exposing bare wires that can short-circuit and cause shocks or fires. Old cloth-insulated wires should be replaced with plastic-insulated wires. Plastic insulation lasts indefinitely and completely resolves the safety issue. Click here for more information about replacing cloth  wiring insulation.

The National Electrical Code requires that outlets in the vicinity of water be equipped with a device called a “Ground Fault Circuit Interrupter” or GFCI (also called GFI). GFCIs are required in all bathrooms, kitchens, garages, pools, and some outdoor areas. GFCIs can protect your family against deadly electrical shocks and are inexpensive to install. Click here for more information about GFCIs and GFIs.

Knob & Tube wiring gets its name from the white ceramic knobs around which wires were wound and the short ceramic tubes through which wires were guided. This type of wiring is usually found in homes built before 1935. In the Los Angeles and some other parts of the country, knob and tube can sometimes be seen in houses built as late as 1950. My electrical company specializes in replacing Knob and Tube wiring in the L.A. area — much of it is in Pasadena and other parts of the San Gabriel Valley.

Knob & Tube systems use old cloth-insulated wires and are not grounded. We strongly recommend that Knob & Tube wiring be replaced to eliminate fire and electrical shock hazards.

An electrical surge is a sudden increase in power that flows through electrical wires. Surges can cause damage to computers, phones, entertainment systems, microwaves, stoves, fridges, washers – any device that has electronic components such as sensors and timers. Today, that’s most appliances. A Whole House Surge Protector can save your appliances and electronic devices and save you thousands of dollars in damage.

Look for our $50 discount coupon for the installation of whole house surge protectors at www.theelectricconnection.com.

A properly grounded electrical system routes occasional leaking electricity through a “ground wire” into the ground. Without grounding, excess electricity can cause fires, damage to electrical appliances and computers, and also shocks to residents.

Older homes built under earlier electrical codes will often have outlets for two-prong plugs. This is often an indication of an ungrounded electrical system. Sometimes, the outlets have been replaced with the modern three-prong type, but without actually adding a ground wire. This can make it appear that the system is grounded when it’s not.

Even when your wiring system has a ground wire, the grounding may fail due to loose or corroded connections and splices. A qualified electrician can check your wiring with a special tester to determine if it’s fully grounded. The Electric Connection offers this testing as a free service with every electrical job that we do in the L.A. area.

There is now conclusive evidence that both Zinsco and Federal Pacific Electric (FPE) “Stab-Lok” electrical panels can fail. (Electrical panels contain your circuit breakers or fuses.) Fires and electrical shocks can result. These brands were installed in the 1950s to 1980s. The failure rates as they age are much higher than for other brands and represent a real electrical hazard. We recommend all Zinsco and FPE electrical panels and circuit breakers be replaced with modern electrical equipment. Click here for more information about Zinsco and Federal Pacific electrical panels. One of the specialties of The Electric Connection is panel upgrades. We’re possibly the most active company in Los Angeles when it comes to electrical panel replacements. We offer a free safety check of your L.A. electrical panel box with every job.

Circuit breakers and fuses protect your electrical wiring from overloads of electricity. Overloading can melt wires and cause fires and electrical shocks. Whenever a wire is overloaded, the circuit breaker or fuse is supposed to cut the flow of electricity.

Sometimes older circuit breakers don’t work fast enough and allow too much current through. Fuses can also be a safety concern. Sometimes, they’ve been replaced with improperly-sized fuses and no longer protect wires from overloading. These safety issues can be solved by installing modern circuit breakers. Click here for a coupon for a free check of your electrical circuit breaker box with your next electrical job.

Most homes have copper electrical wires. However, from the mid-1960s to the mid-1970s, over 2,000,000 U.S. homes were wired with aluminum. The U.S. Consumer Products Safety Commission has determined that aluminum wiring is hazardous as, over time, connections and splices can fail, resulting in fires and shocks.

Fortunately, a qualified electrician can upgrade an aluminum wiring system without replacing all the wires with copper. It’s possible to eliminate the fire hazard by upgrading only connection points and splices. Aluminum wiring safety retrofits should be done only by electricians specifically trained to upgrade aluminum wiring safely.

If you think it’s possible that your Los Angeles home has aluminum wiring, you can get a free checkwith your next electrical job. One of the specialties of The Electric Connection is efficient and effective safety upgrading of aluminum wiring in the Los Angeles area.

Click here to visit our website.

Cities like Colorado Springs, Denver, and Pueblo are constantly expanding and urbanizing—you can always spot a new neighborhood development on your commute to work. New homes are sprouting up all the time, and people are buying. However, sometimes new isn’t always better (or cheaper). There are a lot of great, older homes throughout Colorado cities, and are often a better choice when it comes to real-estate investments. If you currently own an older home, or you are considering purchasing an older home, you’re going to want to check for these common electrical problems that could cause issues in the future in terms of both safety and money.

Generally, homes that were built after 1940 are in the clear—they are usually safe and the electrical systems were installed up to code. Homes built prior to the 1940s should be evaluated, however, as many of the electrical wiring could have deteriorated or may not be able to power a home in this era of modern day technology and appliances. Regardless of when your home was built, it might be a good idea to have an electrician come out and evaluate the wiring systems in your home and ensure that your family will be safe. Here are some things that you can look for yourself when it comes to old wiring in old homes:

Old Cables

Metal cased, fabric covered, or frayed wires are signs that your wiring is outdated and unsafe. Many times during the early 1900s, electrical wiring was “protected” by metal jackets or canvas-like cloth, which can cause problems if the insulation in your walls has been damaged or aged, or even if the metal electrical cords were placed on inadequate grounding. If the wires get exposed, or start to fray in these two locations (next to insulation or on top of a poor electrical foundation) this could be a serious fire hazard waiting to happen. You know you need to call an electrician and get your wiring replaced when you can see any scorch marks on switches or outlets, when you see torn, damaged, or missing insulation, or when you see exposed wires that could potentially cause a fire.

ZINSCO and FPE Panels

Zinsco Panels

While popular around the 1970s, Zinsco panels are almost obsolete today. However, older homes can still have these panels as a part of their home’s electrical system. Not every Zinsco panel needs to get replaced, but it would still be a good idea to get it inspected, as these panels have circuit breakers that have been known to melt into the main bus bar and cause a fire.

FPE Panels

Federal Pacific Electric panels were distributed throughout thousands of homes in the 1950s to the 1980s, and have an unfortunate reputation of being extremely hazardous to the safety of you and your home. These panels have been known for their inability to trip the circuit breaker when the circuit is overloaded or short. When the breaker doesn’t trip, it instantly puts your home at a fire risk because the circuit is taking on much more than it can handle and has no way to shut itself off.

If you recognize either two of these logos on your electric panels in your home, call an electrician immediately to get them inspected.

Old Fuse Boxes—Below 100 Amps of Power

Houses built before the late 1940s and early 1950s were not expected to handle the amount of electricity that we use in modern time. That being said, the homes were installed with a circuit box that can only power 60 amp service (four fuses), or sometimes even 30 amp service (two fuses). This means that your older home may not be able to power all of the appliances and electronics that you have in your house. If your breaker is tripping constantly, or your electric bill is through the roof, this may be a sign that your older home needs an electrical inspection to update the amp-service. Older electrical panels are also at risk of starting a fire. If you are unsure whether or not your home is experiencing this, call an electrician to be safe, and they will be able to give their expert opinion on whether or not you need to upgrade your electrical panel in your older house.

These are just a few signals of outdated electrical work in an older home, but each one is a serious risk to the safety of you and your family. If you have an older house, be sure to get it checked out and evaluated for safety. The same goes for those who are looking to buy an older home in the Colorado area, as the electrical work could be outdated and dangerous.