A bad circuit breaker is a major inconvenience, but there can be other issues at play when your power supply isn’t working the way it should. Breakers protect you and your home from current overloads and other electrical issues. If the circuit gets overloaded, the breaker will trip, cutting power to eliminate the risk of fire. Sometimes a breaker will trip even when there is no overload, but it can be tricky to figure out which situation applies.

If you think you have a bad circuit breaker, look out for the following signs so you can get the problem taken care of quickly.

If your breaker is tripping, it could mean there is a device on the circuit causing an overload. Identifying what circuit the breaker is protecting can help you figure out if the problem is with a device or with the breaker itself. There might be a label on the breaker panel that gives you this information, but if not, you can figure it out by testing your lights and devices. If you disconnect the devices connected to the circuit and try to reset the breaker again, the outcome will confirm whether you have a faulty breaker. If it still trips even without the devices connected to it, it is defective and needs replacement.

Motion sensor LED stair lights let you safely and effectively navigate your steps while eliminating the need for any action. And because they turn off automatically, they also save power! We’ve recently installed these handy little LED stair lights and wanted to share the process with you.

wire that will be needed. It is best to order more than you need so that there’s slack in the line and enough to extend to where your power supply will be mounted.

It’s important to choose the correct wire gauge for the length of wire you need and amount of current that will be flowing through it. The key is to avoid voltage drop, which happens when the supplied energy of a power source is reduced as electric current flows through wire (or any other pieces of equipment that do not supply voltage on a circuit). The longer the run of wire, the lower the gauge of wire needed.

*If you need help determining the correct wire gauge, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

3. Using wiring from the

4. Use a run of wire to join the PIR sensor at the top of your steps with the power supply. You can wire both PIR sensors to the power supply using electrical tape or with

5. Connect your main line to the PIR sensor at the bottom of your steps, and begin connecting each step light with

7. Finally, connect to power.

LED stair lights and

4. Connect your main line to the PIR sensor at the bottom of your steps, and begin connecting each step light with

6. Finally, plug the power supply into your wall outlet.

When it comes to crime, it’s evident that there’s an appeal to darkness. Less visibility means less chance of getting caught. The 2014 National Incident-Based Reporting System (NIBRS)—an annual Uniform Crime Reporting (UCR) Program publication that’s released by the FBI—includes detailed crime data, such as time of day and type of offense. More than 18,000 law enforcement agencies participate in the UCR Program and provide data voluntarily. NIBRS’ Crimes Against Persons data shows that of the 1,093,466 incidents reported in 2014, 562,104 (51.4 percent) were between the hours of 6 p.m. and 6 a.m. Crimes Against Property data shows a lower—yet significant—39.4 percent of 3,493,904 reported incidents taking place between those same hours.

In an attempt to lessen crime and increase energy savings, many cities and businesses have started replacing traditional high-intensity discharge (HID) lights with LED bulbs, light engines, and fixtures. These actions have paid off. In 2008, Los Angeles began a project to retrofit 215,000 lights with LED lights. Since implementation of the project, color-rendering indexes (CRI) than HID fixtures. CRI refers to how accurately a light source reveals the true colors of objects, people, and surroundings. The CRI of an HID bulb can range from zero (high-pressure sodium) to about 65 (metal-halide). LED fixtures are capable of having CRIs of 75 and higher. Lights with a CRI of 80 or higher are considered to show colors most accurately and increase visibility, which is especially important for security purposes and parking lot surveillance.