As a rule, the bottom of any hanging light should be at least 6’8″ off the ground – unless it’s over a table or island. When you have an 8′ ceiling, this doesn’t give you a whole lot of room to play. If you long for the grand impact of a decorative

A room with a single light fixture is depressing. Kick the shadows by adding multiple light sources. A few stylish flush-mount ceiling lights. Some table lamps. An accent light here or there. When you have multiple lights shining in different directions, the space will feel lighter and more open. Make sure to place ceiling lights at least 3′ from the wall, any closer and harsh shadows will make your ceiling seem lower. 

Outdoor LED Decorative String Lights

When paired with vintage LED bulbs, these LED string lights add a spooky feel to your patio. The 21-foot LED light socket strings hold 10 LED bulbs with standard E26 bases. They’re available in in-line styles and are linkable up to 500 watts maximum.

Use this submersible RGB LED Accent Light to give your fountain an eerie glow. Place it under spooky glass decorations or inside a pumpkin, and use the included IR remote to select colors and color-changing modes. This LED Halloween light offers 13 static color modes and two dynamic color-changing modes.

30- or RF Touch-Color Remote (sold separately) or with a Halloween product category.

We talk often about how electricity can be a double-edged sword that can help and but also harm. While making sure your house is wired correctly it is also important that you have put safeguards in place to protect yourself and your valuables from accidents. Surge protectors do just that, and they can be applied to an entire house as well for extra protection. Let’s get into more detail about how surge protection applies to you.

A surge happens when there is an excessive flow of electricity through a circuit or electrical connection. Devices will take in electricity they need to function properly, but in certain cases such as electrical storms or problems in your home wiring, too much electricity will be pumped through the electrical system. Much like taking too much water can be harmful to us, the electrical device will “drown” in the excess electricity and become damaged. This is why we use power bars on many of our larger electronics like computers and TV’s.

Surge protectors will help keep your electronics safe as well as yourself. If there is excess electrical flow, the electricity could jump to a nearby person and seriously injure them. Being smart with your protection and guarding your valuables can prevent you from needing to purchase a new TV or computer after a night of lightning. While we do use surge protectors around our home, it is important to have layers of protection. Similar to a car’s metal design and airbag system, there are layers to protect the person or item behind them.

Entire home surge protectors can be applied to the home’s breaker panel to protect specific circuits from surges. For example if you have an entertainment system on one circuit that requires a lot of electricity to run, it would be a good idea to connect a surge protector on this circuit in the breaker panel. This would add a first layer of protection to the electronic devices, and if a surge does trickle through the first line of defense, the power bar surge protector will protect from the second.

While the home electrical system is designed to protect you and your valuables, accidents happen when you least expect it. Protecting yourself against these situations is important. Contact your local Expert Electrician to find out more about how you can protect your family and your belongings with home surge protectors.

An electrical circuit works as a loop where electricity flows from a source and then returns to that point again after powering the device connected to it. The power flow interrupts or stops if the path is broken. There are also receptacles, fixtures, or switches joined to the course through different types of electrical wiring.

Every electrical circuit has a specific breaker or fuse that controls it. Inside the main electrical panel of your house, you will find reference numbers to identify which breaker or fuse is assigned to which circuit. Mapping of them is a standard electrical safety procedure.

power company supplies electricity to your home through the transmission and distribution lines. The energy enters the service panel, also known as the fuse or breaker box, after passing through a meter. Then, the box has three wires (hot, neutral, and ground featuring insulation of different colors) that do the jobs of transmitting the power to an external outlet, returning to the source, and providing the ground.

The wires of your home are generally installed in three ways:

It’s a wiring system where a single electrical circuit supplies power for several devices. There are various housing boxes from where both hot and neutral wires emerge and run along the route. They branch off to single receptacle and fixture.

It’s the most common of all the systems seen in residential settings.

Switch Wiring

Installed on hot wires, such a system has switches that either transmit or break the current flow to various devices or lighting fixtures. A switch changes its position to allow or interrupt the flow of electricity to electrical machines and instruments.

The system routes the hot wire through various fixtures before joining to the neutral one, which then carries the power to the source. It’s the least used and most inconvenient of all the types because it connects the devices, i.e., lights in a series. So, the circuit breaks off when just one light is burnt out.

Parallel wiring is the best option for household settings because it does not break even when one of the connected fixtures goes kaput. Nevertheless, remember not to run too many electronics from one source because each circuit can carry only a maximum electrical flow.

Once someone has discovered retrofitting as a read that by clicking here.

Let’s get started with the first question on the list, and that is what exactly is a retrofit kit?

What is a retrofit kit anyways? Well, we’ve actually reducing your energy consumption even more. Just make sure you are buying a LED retrofit kit that has the option to be dimmable, otherwise you will NOT be able to dim them.

Retrofit vs full replacement, why should you consider retrofitting with LED?

While a full replacement of an entire is fixture is very valid to do especially when they are outdated or literally falling apart; often times you can avoid that by retrofitting your fixtures. With retrofitting you get to keep your old fixture but just replace the light source in it with a new one. This will allow you to reduce the costs associated with the lighting upgrade tremendously, which will allow you to realize a much larger ROI.

Although there are benefits of both, you need to think about your facility or buildings own situation, and go from there. To recap; retrofitting is great if you can keep your old fixtures but if you can’t (due to reasons like outdated or near falling apart), then a full replacement is probably the better option.

For more info, check out this infographic (

Why should I even switch to LED in the first place?

Very good question, and this not only applies to those retrofitting but for any facility that plans to make a lighting system update. LED technology has vast benefits in almost every area of the definition “quality” for commercial lighting purposes. Here are just a few of the major benefits that more often than not win over businesses to commit to the conversion over to LED technology:

As you can see these are all some pretty big benefits, and that’s only the start. These reasons are why many companies are making the conversion over to LED products from other outdated technologies such as metal halide, HPS, and even fluorescent. Why not convert to LED with a retrofit LED kit and realize all of these benefits and more? It just makes sense!

Is it difficult to retrofit an existing light fixture?

Well, that can depend. To someone who has no knowledge about lighting fixtures and electrical wiring, then yes this will seem like an extremely difficult task. On the other hand for someone who is a professional, this isn’t a difficult task at all.

The process, in theory, is simple because all it consists of (for the most part) is a replacement of all the existing lamps, ballasts, sockets, and brackets with new ones to fit your retrofit kits. If you have no experience doing this, and even if you do, it is always recommended to bring in a licensed electrician if you can to ensure it is done right and to safety standards.

Are LED retrofits that are compatible with existing ballasts a good idea?

You need to consider the age of the ballast that is currently installed. In most cases, it will be nearing the end of it’s life and thus it won’t be the most up-to-date ballast that you could have. This adds for an additional point of failure, which could cost you more down the line in maintenance fees to replace them when they die out.

You have to consider that since you are considering the switch over to LEDs through retrofitting, you most likely haven’t recently upgraded you lighting system or replaced much. This means that the ballasts currently installed are most likely, at best, as old as the lights in your fixtures currently. But more often or not, they are even older than that which can definitely mean they are nearing the end of their lifespan.

Taking this all into account, it’s impossible to tell you if using existing ballasts is a contact us. We will gladly answer any question you may have!