Landscape lighting can add beauty to your home as well as provide increased safety on your property.  Lighting design can be used to light pathways, highlight your homes architecture, and deter intruders.  When considering adding lighting to your landscaping, it is important to find the right balance of lighting.  Focus on adding lighting to main activity areas like driveways, entrances, pathways, dark areas around windows, and stairs and main focal points such as fountains, trees, or statues.  The following landscape lighting basics can help make the most of your lighting.

Up-lighting: Up-lighting is placing a light facing upward toward an object to illuminate it.  This works well for highlighting the focal points of your landscape or home.  Use it sparingly to highlight objects around your yard like statues, trees, flag poles, and fountains.

Down-lighting: Down-lighting is used to illuminate large areas.  It works well for illuminating entertainment areas such as a patio or a deck.  It also helps to deter intruders.

Accent Lighting: Accent lighting is an excellent choice for lighting paths and stairs by placing lights along both edges of a path or a staircase.  This looks beautiful and has the added safety feature of helping prevent people from tripping and falling.  Accent lighting can also add focus to low-lying flowers, shrubs, and ponds.

Advantages of Low Voltage Lighting: As part of your basic landscape lighting, you have the choice between using 120v and low voltage 12v lighting.  Low voltage has a lot to offer in terms of landscape lighting safety as well not having to dig 18 inch trenches into your yard. Low voltage lighting can be neatly tucked away, just below your yard’s surface.  It is safer in wet conditions, and it offers more precise lighting effects.  Because the lamps (light bulbs) are smaller, it allows for smaller, less obtrusive fixtures.  It can also save you money by having lower energy costs.  Low voltage lighting requires a transformer to convert 120v to 12v which can cause voltage drop (dim lights) if it is improperly engineered.  For this, it is a good idea to ask a professional electrician for help.

These tips will get you started.  For more ideas, ask a lighting consultant for suggestions, and for any questions, don’t hesitate to contact www.electricmaninc.com to find the answers you need!

Think your home’s lighting is worthy of sharing? Post to our Facebook Fan Page!

About ElectricMan Inc.

ElectricMan Inc. is one of Dallas’ most trusted electricians. Nick Schaeffer, Mr. ElectricMan himself, has quite the resume for a master electrician. He started the company by himself in 2004 and hasn’t looked back since! For more information about Electricman’s list of electrical repair services, please visit www.ElectricManInc.com

If you’re dying to install your new instructions for how to install a light bar. These instructions include options for installations with or without a wire harness and for connecting to existing LED lights. Installation will vary based on the type of vehicle, existing lighting setup, and chosen wiring method, but these instructions can serve to give you a general idea of the process. Light bar mounting instructions are also available and are listed by WH-DTS10, WWH-DTD30; (ATP) WH-ATPD20, sdoptional mounting brackets; be sure not to overtighten the hardware (you will need to adjust it in step 7).

3. Route the lighting side of the wiring harness from the battery to the light in a safe, secure manner. Connect the harness to the light. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wiring harness is a safe path to follow. Some lights may not have DT or ATP connections on them, but the connectors can be added from the harness kit or purchased separately (ATP-FPT).

4. Continue to route the switch portion of the harness to the desired location of the switch. The switch may need to be unplugged from the harness to make routing of the harness easier. An optional remote-controlled switch (RS-x) are also available with different legends.

5. Connect the black (ground) wire with the large ring terminal from the harness to the negative battery terminal. Connect the red (power) wire with the large ring terminal from the harness to the positive battery terminal.

6. Secure the relay to a suitable location, and test the light to make sure the circuit works.

7. Finally, aim the light in the desired direction, and tighten all mounting hardware.

3. Connect the black ground wire of the new light to the ground wire of the old light with solder and heat shrink tubing (PSC-x). Connect the red power wire of the new light to the power wire of the old light.

4. If the new LED work light or off-road light bar has an ATP or DT connector that you wish to utilize, corresponding ATP (DT-MPT) pigtails are available.

5. Finally, aim the lights in the proper direction, and tighten all mounting hardware.

 

1. Find a suitable mounting location that will allow for running wires and mounting the LED light bar. Mark where your holes will be for the light bar brackets or mounting feet. Check behind drilling locations to ensure nothing will be damaged. Drill appropriate-sized holes.

2. Mount the lights with the provided hardware or with DT-MPT or RRS-SP, RRS-SPx, or RCS-RF25A) under your hood to speed up install time and avoid routing wires through your vehicle’s firewall. Route another run of red wire from the pigtail adapter (connected to the light) to the output terminal of the switch. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wire harness is a safe path to follow.

4. Be sure to double-check for all obstructions and proper clearance. Drill an appropriate sized hole for the switch, and mount it.

5. Connect your black wire to the negative battery terminal. Connect your red wire to the switch input terminal and to the positive battery terminal with an appropriate-sized fuse holder (MAF-x) installed within 18 inches of the battery. You will have to cut your section of red wire to allow for the fuse holder to be installed between the switch and battery. Connect your other run of red wire to the switch output terminal.

6. Finally, aim the lights in the proper direction and tighten all mounting hardware.

Cold winter months bring opportunities for cozy moments indoors  — but also some potential hidden dangers. More than 45,000 electrical fires occur in homes each year, according to thea licensed electrician update any damaged or two-prong outlets.

Sometimes it’s hard to tell if you have old and unsafe wiring because electrical work is mostly hidden behind the walls of your home. Remember, however, that wiring problems are a major fire threat. Pay attention to these signs of hidden electrical issues and then get safe by

Lamps and other light fixtures provide necessary illumination but can also pose a risk. Placing a bulb with a higher wattage than a fixture can handle poses a risk for igniting a fire. Heed the maximum wattage allowed for all fixtures and decrease the wattage or replace ones that seem to get excessively hot when lit.

Never decorate a lamp with paper or cloth that could ignite, and keep fixtures away from textiles, like bedding or curtains. Replace cords that are frayed or damaged.