Being the owner of a plant is a big responsibility and it is very important to keep your equipment in working condition. You need to remember that all your maintenance must be planned in an efficient way for both economic and energy efficiency.

Usually when you choose to partake in your routine maintenance, it may cause a delay in your production resulting in loss of income. All safety electrical equipment that is used on a continuous basis will require a lot more maintenance than your equipment that is used rarely, although they will still need to be maintained.

Even though you may maintain your equipment on a regular basis there will be times that your equipment could break. You will then need to take all costs into consideration before deciding whether you should repair the equipment or to just replace it completely.

To help you decide, you should analyze what you have already spent on the equipment as well as what it will cost to maintain it in the future. Once you have done that you should compare it to what it would cost you to acquire newer equipment that may cost less to maintain.

You could also hire a specialist that could create a breakdown of important factors such as the probability of the following:

To run a successful plant you will also need to keep the following important steps in mind:

Any time of the year is a good time to save money, especially when it comes to the issue of one’s electricity bill. However, it is very understandable that the summer season is when one’s electricity bills tend to go straight through the roof because of the increasingly hot weather! This summer season, make sure that you end up saving some money on your electricity bill with the following energy savings cost cutting tips.

For starters, make sure that you keep your TVs and also your lamps quite a distance away from your thermostat. You see, both TVs and lamps emit heat, therefore prompting your air conditioning to actually run excessively and more than it really has to! Instead, place your TV and lamps across the room and think hard about switching to compact fluorescent bulbs.

Insulation is yet another thing you should do properly if you want to attend to your energy savings and your summer electricity cost cutting steps. You ought to insulate in an intelligent manner, for one thing. This means that you should look to insulate in some areas more than others, such as the attic. When you insulate your attic, you actually lower the negative effects of the heat that stem from the scorching rays of the sun. If you do this correctly, you are going to stop the heat that tends to build up on top of your home from actually filtering down to the rest of the residence.

Sometimes, your summer electricity cost cutting measures are so simple that they may even seem deceptively…simple! Take for instance the issue of your windows. When days get really, really hot in the summer months, just remember to close either your blinds or your curtains prior to leaving for work in the morning. This will minimize the effect of the sun’s blistering rays from beating down into the various rooms of your residence, thereby warming up your home to unbearable levels. As a sweet bonus, the fading effect of the sun’s rays to your rugs and your furniture will also be minimized.

Finally, you should use your microwave more than the oven for when you are preparing dinner. If you utilize your microwave, you can efficiently get your dinner ready in just a few minutes rather than an hour, and you will also be generating a lot less heat than if you utilize your oven!

So as you can verily see, there are a lot of things that you can do with regard to saving some money on your electricity bills over the summer. All that matters is that you have to be committed to adopting some of these money saving tips over the summer.

There are many reasons and advantages of LED street lights over HPS, Metal Halide, and any other HID light used in the street lighting industry. These advantages of LED street range from cost savings, higher quality of light, and overall better efficiency.

LED is quickly becoming the “go to” light for all uses; residential, commercial, and industrial. From fully replacing and retrofitting LED is seriously becoming the majority within the world of lighting. The following list is going to cover 4 major advantages of LED street lights over HPS and Metal Halide, hopefully it shines some light on the true benefits of LED for even Metal Halide, you get results that show LEDs actually really do pay for themselves. If you use your lights often, making the switch to LED street lights may even pay themselves off within a few years.

If you’d like to see how much you could save, check out the diminishes over time. This is a highly important thing to note because with greater lumen depreciation comes added costs of maintenance.

Lighting fixtures such as HPS and Metal Halide have lumen depreciation that happens much earlier in their life and much quicker throughout the bulbs life. Whereas an LED takes a longer time to start depleting in it’s lumen output and much slower lumen depreciation than HPS and Metal Halide does.

While not all LED suppliers and manufacturers, MyLEDLightinGuide.com offers LED fixtures and retrofit kits that can produce at a very high MyLEDLightingGuide retrofit kits can run as high as 151 lumens per watt. While the typical retrofit kits on the marketplace (on average) run at only around 110 lumens per watt.

This is just a prime example of how powerful lumens per watt can be. The more lumens per watt you get, the less watts you will need to produce the same amount of light.

So, let’s compare the “average” retrofit kits compared to a Metal Halide light. Remember, the “average” retrofit kits run at around 110 lumens per watt. Compare that to a Metal Halide light that runs around (on average) 90 lumens per watt.

So just by these numbers we can start to see the power LED lights have and how they need less watts to produce the same amount of light that a HPS or Metal Halide light does.

In addition to #3 on this list, LEDs also provide a higher quality of light measure by the Color Rendering Index (CRI). Here’s two images that should do the talking:

Street Light Conversion From 400W Metal Halide to 120W LED using a LED Retrofit Kit (before)

As you can see after the 400W Metal Halide was replaced by the 120W LED fixture, the light produced is much brighter and illuminates a greater area. On top of that, it is using way less energy (400W down to 120W)!

Brighter and greater illumination can greatly increase safety and reduce crime by the simple fact of being able to see more throughout the night. Better illumination also creates safer roadways by not leaving any dark spots that may cause issues for drivers during night time driving.

Here at Kolb Electric, we’ve had numerous business owners throughout MD, DC, and VA approach us for more information about commercial light-emitting diodes—more commonly referred to as LEDs. Businesses everywhere have been forced to find ways to reduce their monthly expenses and save money in order to survive in these challenging economic times. Transitioning to commercial LED lighting is one of the ways businesses in the area can save money and enjoy other benefits as well.

Commercial LED lighting is very energy-efficient—replacing incandescent, halogen, or compact fluorescent light bulbs with LED lighting reduces energy consumption 50 – 85 percent. Some studies reveal that businesses have the potential to save as much as 60 percent on their electricity bill each month by making a total change from incandescent bulbs to LED lighting. ENERGY STAR reports that lighting is the largest cost component of a commercial building’s electricity bill and a significant portion of the total energy bill.

Some businesses shy away from LED bulbs because of their higher initial cost compared to other bulbs.  However, it will not take long for businesses to recoup this cost in the form of direct savings on electricity bills. Also, LED bulbs work by generating light using a semiconductor rather than relying on heating up a traditional filament. What does this mean for you? It means the highest quality LED bulbs can last up to 50,000 hours. The typical incandescent bulb, on the other hand, lasts only about 750 hours.

Work environment upgrades are closely tied with an improvement in the performance of employees. A Cornell University study estimates that a 3 – 5 percent gain in worker performance can be achieved with better lighting. In many cases, the gains in worker productivity alone are enough to offset the costs associated with commercial LED lighting. Light has a direct correlation with ease of reading, lower eyestrain, reduced errors, better turnaround time, reduced risk of musculoskeletal injuries, and psychological well-being.

The great thing about commercial LED lighting is that it can be tailored to meet your needs for color accuracy. Whether you want lighting that’s warm, cool, or neutral, the right type of LED lighting is available. Color rendering—the ability to make colors look true—must also be taken into account when it comes to LED lighting. The color rendering index (CRI) characterizes light sources in view of their ability to produce “natural light” and can be between 0 and 100. The closer an LED light comes to 100 on the CRI, the more naturally colors are rendered, and the light is perceived as more pleasant.

Transitioning to commercial LED lighting can help you save immediately on your electricity bills. The fact that LED lighting lasts significantly longer than incandescent bulbs and has the potential to improve employee performance is also beneficial to your business. If you want to learn about what type of commercial LED lighting is best for your business, contact us today.

The London Olympics are certainly on the tip of nearly everyone’s tongue (and Courtesy of FrenchArt-Deco.com

This piece, entitled “Swimming Pool” by French artist Albert Decaris won gold in the Engravings and Etchings competition.

In 1949, the International Olympic Committee decided to stop all art competitions, reasoning that it was illogical to let professional artists compete, while only amateur athletes were eligible. Instead, cultural festivals replaced the art competitions, and still do to this day. There’s still a chance for the best of the best artists and entertainers to showcase their stuff on an international stage, and for lighting designers, this is certainly a world class exhibition. 

LED is the light source that’s in it to win it this summer, wowing Olympic fans with spectacular light shows and festive monuments alike.

At the opening ceremony, LEDs were at the center of almost everything. The dove bikes used LEDs to light up their wings as they performed a circuit of the stadium.

LEDs lit the screen showing the Queen’s acting debut, with none other than James Bond.

Even on the sidewalk outside the main Olympic Stadium, there are 20 circular slabs that capture the kinetic energy of pedestrians’ footsteps to light up nearby LED lamps for 30 seconds at a time!