There’s a lot more to the cost of a light bulb than the price tag sticker. There’s the impact on your electrical bill, the tally of replacement bulbs you’ll need to buy, and the time you have to factor in for maintenance. Sure, the light bulb in your table lamp may take just a few minutes to replace, but what about your recessed cans that are two stories away from easy access?

We published an infographic on Lighting Facts, a program of the U.S. Department of Energy, created the one below, showing the five-year-cost of 100 watt equivalent light bulbs. As you can see, the low purchase cost of an incandescent light bulb doesn’t necessarily pay off in the end:

Capitol Lighting created a friendly competition challenging local designers to create one-of-a-kind bathroom spaces and put a call out to all Northern New Jersey-area interior designers to participate. Two top designers were chosen out of numerous applicants to compete in the unique challenge of remodeling the men’s and women’s bathrooms at the company’s Paramus showroom — one of which will be crowned the “Thronedown” champion. The finalists were chosen based on previous work and have been given a $2,000 project budget with lighting supplied by Quoizel and Feiss.

Anna Maria Mannarino- Mannarino Designs, Inc.

Aluminum LED profile housings allow you to create customized light fixtures with LED strip lights. Our Klus brand LED channels are available in many different styles, including recessed-, or flexible, O-shaped, and more. Available in 1- and 2-meter lengths, the channels can be easily cut for any application from under-cabinet lighting and bookshelf lighting to showcase lighting and transition strip lighting. They’re available with a variety of lens options, such as clear, frosted, and etched that complete the profiles. We’ve put together a step-by-step guide for using these channels to create your own light fixtures. Please note that your specific channel might vary from the one used in this tutorial.

Materials needed:

1. With a pair of clippers, carefully clip through the clear plastic heat shrink as shown in figures A-C. You will want to take your time and be careful not to cut the strip’s wires while removing it.

2. Lay the LED strip into the channel, and position it along the bottom so that the ends of the strip and the channel are lined up (fig. A). Now, remove the paper from the strip’s adhesive backing (fig. B), and adhere the strip to the LED channel—starting at the lined end and working your way to the other end of the strip. Be sure to leave roughly 1/4-inch free at the end of the channel so that you can install the end cap as shown in figure C.

3. If one of your end caps doesn’t come with a pre-drilled hole, you will need to drill your own to allow the wires of the LED strip light to come through. In this case, we used a Dremel tool, but other options are viable as well. Regardless of the tool you choose, it is helpful to mark the end cap where you would like the wires to come through. Start the hole small, and increase the size as necessary.

4. Place the end cap on the wired side of the strip by threading the wires through the end cap as shown in figure A. Insert the end cap into the end of the light bar, and push firmly until it is fully in place (fig. B).

5. On the open end of the bar, slightly peel up the end of the LED strip (fig. A); this is necessary to install the end cap. Now measure your channel lens, and trim off the excess with clippers (fig. B). Be careful when trimming to avoid cracking the plastic. Excess material can be lightly sanded off. Once the lens has been cut to the proper length, slide it into the channel, and install the end cap as shown in figures C and D.

6. That’s it! Your customized LED light fixture is complete and ready for installation, which we will cover in the next step.

7. Mounting this LED profile is as easy as applying double-sided tape to the back of it and sticking it to your intended surface. Be sure to cut the tape to fit the back of the LED profile and to leave the tape backing on the side not attached to the channel until you are ready to mount it.

For most LED profiles, mounting clips are available for a more permanent installation.

If you have questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nunc sit amet velit non lectus ullamcorper vestibulum. Morbi semper augue vitae vulputate convallis. Morbi sed ante at leo cursus efficitur. Proin nec ante sed nunc dapibus fringilla eget finibus lorem. Vestibulum nulla urna, efficitur sed sollicitudin at, venenatis quis neque. Nulla imperdiet nibh et ex pulvinar ultricies. Ut arcu tellus, tempor ac mauris id, rhoncus pretium neque. Sed sit amet molestie mi, at maximus lacus. In sit amet risus hendrerit turpis auctor tempor.

Integer justo lectus, tempus ac faucibus in, dignissim et diam. Ut at metus non ante dignissim interdum vitae a sem. Cum sociis natoque penatibus et magnis dis parturient montes, nascetur ridiculus mus.

Maecenas finibus rutrum facilisis. Integer porttitor in diam eget iaculis. Nam varius tortor vel diam aliquet consequat. Suspendisse at volutpat neque.

Vestibulum egestas lectus quis justo pulvinar blandit. Cras sit amet mattis ligula. Quisque convallis hendrerit felis, et vehicula lorem auctor eu. Fusce fermentum lacinia erat, ut iaculis sem sollicitudin at. Curabitur convallis, ipsum at viverra placerat, odio lacus commodo erat, sed tincidunt mauris massa sed mauris. Pellentesque orci urna, venenatis eget velit sit amet, blandit accumsan neque. Curabitur ultrices dui quis faucibus interdum.